• Home
  •  > 
  • Android
  •  > 
  • How to set up channels on a digital television set-top box. How to connect digital television

How to set up channels on a digital television set-top box. How to connect digital television

To configure the built-in DVB-C tuner to receive digital cable television programs, you must use the following parameters (selected in the TV menu):

  • Initial broadcast frequency - 298 MHz (298000 kHz);
  • A total of 16 transponders with a step of 8 mhz;
  • Symbol rate - 6875 Ksim/sec;
  • Modulation - 256 QAM.

These parameters are suitable for tuning based on the network search principle; if the TV does not support it, then you need to use a full search or select frequencies for manual tuning in megahertz: 298, 306, 314, 322, 330, 338, 346, 354, 362, 370, 378, 386, 394, 402, 410, 418.

Digital TV setup example

1. SAMSUNG TVs

Decoding of SAMSUNG TV models:

  • Country - Slovakia, Slovenia or Others;
  • Auto search for digital and analogue channels;
  • Source - Cable;
  • Search mode - Network.

General algorithms for setting up digital and analog channels for various models of SAMSUNG LCD TVs:

  • Click on enter the menu;
  • Select from the menu - “Channel” (icon “Satellite dish”);
  • Select - “Auto-tuning”;
  • Select - “Digital”, “Digital and Analog” or “Analog” (depending on the preferred television signal); Click “Start”.

Detailed description of setting up digital channels on SAMSUNG brand TVs starting in 2010:

  1. In order to set up digital TV channels for the vast majority of SAMSUNG models, press the “Menu” button on the remote control, the TV menu will open in which you will need to select the “Channel” section (Satellite dish icon).
  2. Make sure that the Cable option is selected in the Channel-Antenna menu
  3. To select a country, go to the “Channel-Country” menu item. The TV will ask for a pin code, if you have not changed it, then enter 0000
  4. To have the necessary DTV search parameters, make sure that the following settings are selected in the “Channel-Country” menu: Country -> Digital channel: Other; Analog channel: Eastern Europe
  5. Open the “Channel-Cable Search Options” menu: Start frequency: 298 MHz (298000 kHz); Ending frequency: 418 MHz (418000 kHz); Baud rate: 6875 KS/s; Modulation 256 QAM;
  6. Open the “Channel-Auto-Tuning” menu: Signal source: “Cable”; Channel type: “Digital and analogue.”; You choose the type of channels at your discretion; you can find only digital channels, or digital and analog, or only analog. Click "Next"; Search mode: “Network”.
  7. Click the "Next" button. Once the channel search is complete, click OK. After an automatic search, all digital channels existing on the cable network will be found. Only those broadcasting in unencrypted form will be shown. It is most convenient to remove the remaining channels.

Removing channels:

  • Open the “Channels-Channel Manager” menu or press the “CH LIST” button on the remote control.
  • Select the desired channel (or several, using the “C” (yellow) button on the remote control), press the “TOOLS” button on the remote control and select “Delete”.
  • After confirmation, the selected channel will be deleted.

Channel sorting:

  • To sort the channels, select the one you need (in the “Channel - Channel Manager” menu, or press the “CH LIST” button on the remote control), press the “C” button, then the “TOOLS” button, the “Sorting” menu and move it to the desired position place in order.
  • If you have a SMART TV: Look at the “smart hub” button on the remote control, click and select the channel icon, then see the list of channels, select editing in the upper right corner.

2. LG TVs

General algorithms for setting up digital and analog channels for various models of LG LCD TVs:

  • Press the button - “Menu”;
  • Select from the menu - “Options”;
  • Select - “Auto-tuning”;
  • Select the country - “France, Switzerland, Sweden or Finland”;
  • Select the signal source - “Cable”;
  • Select - “Digital”;
  • Click - “Search”.

Setup takes approximately 5-10 minutes.

Detailed description of setting up digital channels on LG TVs:

  1. In order to set up high-definition digital TV channels on the vast majority of LG models, press the “Menu” button on the remote control, you will see the TV menu in which you will need to select the “Options” section.
  2. Specify the country "Russia".
  3. Go to the “Settings” menu, “Auto search” item and specify the method of connecting to the TV “Cable”.
  4. In the window that opens, go to “Settings” and enter the following parameters: Search type: “Quick”; Frequency: 298000 (kHz); Speed characters: 6875; Modulation: 256 QAM; Network ID: auto.
  5. If you did everything correctly and saved all the changed parameters, then during the search your channels will be detected.
  6. An important feature of LG TVs is “Automatic channel update” function. It must be disabled, otherwise the TV will periodically reset the channel list you have configured. To do this, go to “Digital cable settings - Channel auto update”: Off

Channel sorting:

To sort channels, select “Settings” -> “Auto search” -> “Cable” -> Uncheck (√) from “Auto numbering” -> “Run”. After setting up all channels, the necessary buttons will appear in the “Program Editor”.

3. SONY brand TVs

Since not all SONY models are equipped with a digital tuner for cable TV (DVB-C), you need to check the model of your SONY TV. Models equipped with a DVB-C tuner are marked KDL-**EX*** or KDL-**NX*** - for example KDL-2EX402R2, the first 3 letters in the model name (KDL) indicate that the TV is digital.” In models KLV-**BX***, etc. There are no DVB tuners.

General algorithms for setting up digital channels for various models of SONY LCD TVs:

  • Press the “MENU” button (for some models it is called “HOME” on the remote control (hereinafter referred to as the remote control). This button is usually blue;
  • Select the item “Settings”;
  • Find the “Digital Configuration” menu in the list of settings and enter it;
  • Select “Auto search for digital stations”;
  • A source selection window will open - select the TV connection type. Select "Cable";
  • In the scan type selection item, select the “Full Scan” mode.
  • Or by selecting the “Manual” item, enter: Frequency: 298 MHz (298000 kHz); Access code: "Auto"; Symbol rate: 6875.
  • Next, click “Start” and wait until the TV finishes searching for channels.

Pay attention to the bottom of your TV's OSD menu. The bottom menu bar displays hints on which remote control buttons to perform certain actions in the TV menu.

4. PHILIPS brand TVs

  1. Press the “Home” button on the remote control
  2. Select “Search for channels”
  3. Select “Reinstall channels”
  4. Select the country “Germany”
  5. Select “DVB-C cable”
  6. In the list of operators, select “Others”
  7. Press right on the remote control and select “Settings”
  8. Set frequency scanning to “Full”
  9. Set the transfer speed to “Manual”
  10. Set the transfer speed to “6875”
  11. We will turn on analogue channels only if they are needed.
  12. Click “Done”, return to the previous menu
  13. Let's start the search

Alternative option

To set up a PHILIPS brand TV, first read the stickers on the back of the TV, where separately for each tuner (DVB-T and DVB-C) there is a list of countries in which, according to PHILIPS, there is digital broadcasting (at the time of release of the TV, but If you update the firmware through their official website, then this list may change in subsequent firmware). If Russia is not in the list, then select Slovakia, Slovenia or Others.

General algorithms for setting up digital channels for various models of PHILIPS LCD TVs:

  • Click on the icon - “House”;
  • Select - “Installation”;
  • Select “Search for channels”;
  • Select - “Reinstall channels”;
  • Select - Country - Russia or Others. If Russia is not in the list, then select - Slovakia, Slovenia or Others;
  • Select digital mode - “Cable (DVB-C)”;
  • In the “Network frequency” line, enter the frequency - 298 MHz (298000 kHz);
  • In the “Transmission speed” line, enter the speed - 6875 Ks/s;
  • In the line “Scanning frequencies” - 256 QAM.

Setup takes approximately 5-10 minutes.

Detailed description of setting up digital channels on PHILIPS brand TVs:

  1. Press the "Menu" button on the remote control;
  2. In the TV menu that opens, select the “Configuration” section;
  3. Select the "Install" tab;
  4. After clicking the "OK" button, you will move to the second menu field, then go to the "Channel Settings" tab;
  5. After clicking the “OK” button, the third part of the menu will open, where you need to select “Automatic”. installations";
  6. Next you will see a message about updating the channel list. Click "Start";
  7. Select "Reinstall channels";
  8. In the “Country” section you must select Russia, but if this country is not in the proposed list, then select Slovakia, Slovenia or Others;
  9. Since you are connecting to digital television via a DVB-C cable network, you must select “Cable”;
  10. Before you start searching for channels, select “Settings” to manually correct the search parameters;
  11. Set the baud rate to manual mode. In the tab, change the transmission speed manually from the control panel to the desired one. In some TV models, the flow rate is indicated in the “Character 1” tab; “Character 2” is left at 0;
  12. Now set the network frequency to manual mode and enter from the control panel:
  13. Frequency: 298.00;
  14. Data transfer rate: 6875 ks/s;
  15. QAM: 256.
  16. After clicking the “finish” tab, you will again be taken to the channel launch menu, now you can start scanning.

If you did everything correctly and saved all the changed parameters, then during the search your channels will be detected.

5. TVs of the PANASONIC brand

Setting up digital channels on PANASONIC brand TVs:

Option 1

  • Press the “Menu” button;
  • Select the item “Settings”;
  • In the window that appears, select “Menu analogue. settings";
  • In the window that appears, select “Add TV signal”;
  • In the table that opens, put a tick in the “DVB-C” line;
  • Click “Start auto-tuning”;
  • After searching for all digital channels, going to the main menu in the “Settings” item, the line “DVB-C setup menu” appears. By selecting this item, you can adjust the setting manually (set the frequency to 298 MHz (298,000 kHz) and speed to 6875 Ks/s).

The menu of your TV may differ from the model offered. In this case, you need to find tabs that are similar in meaning. If your TV asks for a search step, enter 8 MHz.

Option 2

  • Press the “Menu” button;
  • Select the item “Settings”;
  • Go to the subsection “DVB-C Settings”;
  • Select the “Auto Configuration” subsection;
  • In the “Auto Configuration” menu enter the following values: Frequency: 298 MHz; Symbol rate: 6875 Ksim/s; Note that there is no “modulation” parameter. Search mode: “All channels”; Scan mode: “Fast” (or “Full”); Network ID: "auto".
  • Click on “Start scanning automatically”.

Channel scanning lasts from 3 (“Fast”) to 10 minutes (“Full” scanning), after which the TV automatically displays a list of all channels configured by this tuner. The channel list will be displayed automatically, or it can be found in the DVB-C setup menu.

6. SHARP brand TVs

Setting up digital channels on SHARP brand TVs:

Models: 46 (52, 65) XS1, LE700. If your TV model provides for the reception of digital channels, but there is no “DTV MENU” item, then first select another country - Slovakia, Slovenia or Others.

  • Press the “DTV” button;
  • Press “DTV MENU”;
  • Select “Installation”;
  • Select “Auto installation”;
  • Click "OK".

Setup takes approximately 5-10 minutes.

7. DUNE HD brand media players

DUNE HD TV-102W-C can also act as a set-top box for watching digital television (cable (DVB-C) and Internet television (IPTV). Settings:

  1. Go to the main menu by pressing the “TOP MENU” button on the remote control;
  2. Select “Settings”
  3. Select “Applications”
  4. In the “Cable TV” or “DVB-C” section, enter the following values: Network scanning: No; Initial frequency, kHz: 298000; Final frequency, kHz: 418000; Interval: 8 MHz; Modulation: QAM 256; Symbol speed, kS/s: 6875
  5. Confirm the scan by pressing the “OK” button
  6. To view channels, go to the main menu by pressing the “TOP MENU” button on the remote control
  7. Go to the “TV” section
  8. Select “Cable TV” or “DVB-C”
  9. To start watching TV, select any of the found channels

It is difficult to imagine life in our world without information technologies such as the Internet, television and telephone. They are firmly rooted in society and represent an important attribute of comfort. However, not all users know how to connect digital TV at home, so they often encounter certain difficulties when setting up the device.

General information

Recently, there has been an increase in the popularity of digital television. Unlike traditional analogue systems, this type of TV has a lot of significant advantages, providing maximum image and sound quality.

And when it comes to connecting “digital” to a TV, many people think that this is a very complicated process that requires professional help. But in fact, everything is resolved in a short time and does not require much effort. It should be noted that there are two types of digital TV on the market:

  1. Cable.
  2. Essential.

The first type is connected via a special television cable, and the second requires the presence of a special antenna. When the TV does not have a digital receiver, you will have to purchase it additionally. In stores, these devices are sold in the form of a special console.

If your home TV is already equipped with a digital receiver, then all that is required for operation is to install a digital TV smart card with connected provider services. After this, the device will automatically find a list of channels and save them in memory.

If you don't have a receiver, you need to buy a set-top box. It is very good if the TV has an HDMI output, since it transmits the best picture and sound.

Advantages of modern systems

Despite the development of digital television systems, many people still use cable television. It also gives a good picture and unlimited possibilities in choosing channels. However, for such TV you have to pay a subscription fee, which, unfortunately, is constantly growing. Regarding digital equipment, then it has the following advantages:

Receiver selection

To successfully launch digital television in a private home, you need to buy a special device - a digital signal receiver. It uses a device operating according to the DVB-T2 standard. As already mentioned, many modern TV models are already equipped with a built-in digital TV module, so the task can be significantly simplified.

The capabilities of a device are determined by its price range. The most affordable receivers do not support additional functions, while more expensive devices have a small amount of memory and are capable of working with flash drives. Also, some models have the ability to record streaming video to removable media.

Given the wide variety of digital receivers, choosing the right option can be problematic. But if you follow some tips and recommendations, this task can be solved without much difficulty.

If you miss the technical aspects and complex radio-mechanical properties of the digital tuner models available on the market, then all that remains is to study their aesthetic features and set of functions. This approach will simplify the selection of a quality device and make it successful.

If you want to purchase a digital receiver, it is important to decide in advance what functions are needed for television and what you can refuse. The most key and necessary functions include:

  1. Ability to watch television channels in DVB-T2 format.
  2. The ability to use the tuner as a media player to play audio files, view images and other content.
  3. Access to the global network (some models are able to work with media services YouTube, IPTV, online cinemas, weather and news resources, etc.).

If the receiver model supports the above functions, it remains to understand some visual features. When choosing a case material, it is advisable to give preference to devices made of high-quality metal or plastic. These materials are known to have maximum reliability and a long service life.

The front panel of the tuner should contain control buttons, as well as various light indicators. There should be USB inputs and other high-tech interfaces at the back.

Buying an antenna

For DVB-T2 format receivers, conventional terrestrial antennas capable of operating in the UHF range are suitable. In this regard, many TV viewers believe that there is no need to buy a special antenna, stopping only at buying a set-top box. But this is a huge misconception, because old equipment cannot produce a sufficiently high-quality signal and convert an analog channel into a digital one. The digital stream is broadcast in parallel with the analog one at completely different frequencies.

There is another myth that says that powerful digital set-top boxes can transmit images without an antenna at all. But in practice this is impossible, although with good coverage it is enough to install a small piece of wire into the antenna input for the TV to begin receiving a signal. But such cases are rare.

If the house already has an over-the-air antenna, but it does not transmit an image, then you need to perform several steps and diagnose the equipment. If you don’t have such a device, it’s better to buy a more powerful model for digital TV.

It should also be noted that outdoor antennas are always more powerful than indoor ones, even if the latter are equipped with advanced receivers and amplifiers. Unfortunately, many TV viewers buy compact models from online electronics stores, although you can buy a good outdoor version for the same price.

As for indoor antennas, they can only be effective in cases where the television tower is located within a populated area. At a significant distance from the city, such equipment will be ineffective and even useless. For such conditions you will have to buy an external antenna. Before purchasing, you should study the digital signal coverage map in detail to determine where the nearest broadcast points are located.

Additional items

Also, for successful operation of digital television, you need to buy several additional elements. Among them is an amplifier. Many indoor and outdoor antennas already have this device, and the receiver only amplifies the signal. In this case, the transfer of information occurs confidently and without failures.

However, you often have to buy a separate amplifier. To make sure whether it is needed or not, just check the signal quality with the DVB-T2 receiver by entering the system settings with the appropriate scale. If, after connecting the antenna to the receiver, the signal level is 75%, and the picture quality is quite normal, then an amplifier may not be needed. If the indicators do not reach this mark, and the image is transmitted with significant interference, the purchase of an amplifier will become a prerequisite.

Also, to connect digital TV, you need to purchase a coaxial cable, which is capable of transmitting the signal from the antenna directly to the receiver. It is advisable to give preference to models with a copper circuit and screen, since they are characterized by high quality picture transmission, long service life and reliability. When choosing a cable, you should pay attention to its braiding, because the stronger it is, the longer it will last.

If the receiver has an HDMI connector, you must purchase the appropriate cable to connect to the TV. Experts say that this standard guarantees the best quality transmission of pictures and sound. If HDMI is not available, you will have to use traditional SCART, RCA cables, etc.

Installation of devices

When installing a digital television system, the first thing you need to do is install the antenna. If an indoor model is used, then it must be placed near the window, since the best signal level is observed there. As for the external elements, they are installed on the balcony or near the window using brackets.

The antenna equipment is directed towards the location of the TV tower, which will have a positive effect on the quality of reception. Then you need to lay the cable from the antenna to the receiver. If there is no stable signal, the antenna is placed on the roof of the house and turned towards the TV tower. To correctly determine where the television tower is located, it is enough to look where the neighboring antennas are directed.

Next, you need to unpack the receiver and connect the antenna cable to it. After turning on the receiver's power, you should make a number of initial settings, selecting the appropriate language, time and time zone. With the support of the automatic channel scanning function, there will be no special difficulties in setting up. The system will do everything on its own.

At the setup stage, you need to find the channel of the first multiplex and scan it, and then repeat similar actions with the second device. According to experts, each of these multiplexes has about 10 channels. During the procedure, you should pay attention to the signal level. It will be displayed in the settings menu as a special scale. If the reception level is too weak, you need to rotate the antenna and find the optimal direction, guided by the data from the scale.

Setting up digital television

How to connect digital TV is a hot topic for modern TV viewers, because after purchasing the appropriate devices, many users do not know how to configure them correctly. To quickly solve the problem, you need to follow the step by step guide:

It's worth noting that the list of available channels may change over time, so you should periodically rescan for updates. If unexpected problems arise during the tuner setup stage, you must study the instructions again. If the problem persists, then you should contact your equipment and service provider for help.

It is not difficult to understand how to connect free digital television to your TV. To do this, just follow the step-by-step instructions that come with the receiver, follow the advice of professionals and be careful. The system will do the rest on its own.

To connect your TV to the digital terrestrial TV network to receive the DVB-T2 standard, you need a digital TV capable of receiving DVB-T2, or a digital DVB-T2 receiver that decodes the digital signal from the antenna.

The type of digital receiver required depends on your TV - for newer TVs with a composite audio/video input (RCA), digital video DV input (Digital Video), an interface for high-definition multimedia HDMI (High-Definition Multimedia Interface), a corresponding receiver with an appropriate exit. If you have a TV that does not have a composite input, you need a receiver with a SCART output.

For older televisions without the above inputs, a receiver with a television radio signal output, connected to the antenna socket of the television, is suitable. In this case, there is no possibility of viewing analogue programs (if it is not provided by the receiver).

First you need to connect the antenna, receiver and TV with the appropriate conductors, depending on the interface used: (DVB-T2 tuner built into the TV, RCA, DV, HDMI, SCART, RF signal) as shown below.

Let's consider the connection diagram if it is possible to receivedigital TV directly from a TV with a DVB-T2 tuner:

To do this, you will need the TV itself, an antenna for receiving a UHF TV signal and an HF connecting cable. After meeting these requirements and the necessary connections, select the image source “Digital Terrestrial Television DVB-T2” in the TV menu and perform an automatic channel search according to the instructions for the TV.

Let's look at the connection diagram via the HDMI interface:

To do this you will need: a TV that supports the HDMI high-definition standard, a digital receiver with HDMI support, an antenna for receiving a UHF TV signal, and connecting wires. After meeting these requirements and the necessary connections, select the HDMI input type on your TV and automatically scan for channels in the receiver according to the instructions for the receiver.

Let's look at the connection diagram via the DV connector:

To do this you will need: a DV digital video input, a digital receiver with a DV connector, an antenna for receiving a UHF TV signal, and connecting wires. After meeting these requirements and the necessary connections, select the DV input type on your TV and automatically scan for channels in the receiver according to the instructions for the receiver.

Let's look at the connection diagram via a composite RCA connector:

To do this you will need: a TV with a 3RCA input, a digital receiver with a 3RCA output, an antenna for receiving a UHF TV signal, connecting wires. After meeting these requirements and the necessary connections, select the AV input type on your TV and automatically scan for channels in the receiver according to the instructions for the receiver.

Let's look at the connection diagram via a SCART connector:

To do this you will need: a TV with a SCART connector, a digital receiver with a SCART connector, an antenna for receiving a UHF TV signal, and connecting wires. After meeting these requirements and the necessary connections, select the AV input type on your TV and automatically scan for channels in the receiver according to the instructions for the receiver.

Let's look at the connection diagram via the antenna input of the TV

(suitable for all types of TVs):

For this you will need: any TV, a digital receiver with a radio frequency output, an antenna for receiving a UHF TV signal, connecting wires. After meeting these requirements, perform an automatic search for channels in the receiver according to the instructions for the receiver, using an automatic channel search (if available) to search for a channel from the receiver. In this case, the ability to view analog channels disappears (if it is not provided by the receiver).

Antennas

To connect terrestrial digital television, as with regular analog TV, you must use a receiving antenna. The choice of the receiving antenna, according to its characteristics, is individual for each subscriber based on the distance from the transmitting station, the level of the received signal, and the conditions of line of sight to the transmitting station. It could be like efficient antennas with high gains with a suspension height of 10 meters or more, as well as indoor antennas. It should also be noted that the concept of a “digital antenna” does not exist and in most cases, reception of DTTV programs will be possible on the antenna that already exists at the subscribers.

The only recommendations can be the use of modern certified efficient antennas with narrow directional patterns and tuning the antenna in azimuth as accurately as possible in the direction of the transmitting station (for example, wave channel antennas or log periodic antennas).

In addition, we draw attention to possible problems with the reception of digital and analogue TV when using antennas of the “Polish grid” type (download).

Receivers

As shown in the picture. To receive DTTV, you must use either a digital set-top box, often called a “Set-top-Box,” or a TV with a built-in DTTV receiver.

Receivers must receive and decode a digital signal in the DVB-T2/MPEG4 standard.

Compliance of receivers with technical requirements for them, recommended by the Ministry of Communications and Mass Media of the Russian Federation (download).

How to connect and configure

For digital receivers built into the TV, the connection is simple by connecting the RF reduction cable from the antenna to the TV.

If a digital set-top box is used to receive DTTV, the HF cable is connected to it. To connect digital set-top boxes to the TV, various connection options are used, which also depends on the capabilities of the set-top box. As a rule, the standard options are connection via an RF cable, via a composite cable (CVBS), component video output (YPrPb), and for modern TVs via HDMI.

Setting up TVs and set-top boxes for each model is individual, however, as a rule, they are simple by analogy with analog TVs or connecting a satellite receiver to a TV.

Source

How to install, connect and configure digital terrestrial receiver TV DVB T2

First we need to connect our receiver to the TV.

Here is the receiver and its complete set.


In this video, I connected a digital terrestrial TV set-top box DVB T2 Rolson RDB 514 to an old Samsung CRT TV.

Make sure your TV has a built-in digital signal receiver.

TVs with a built-in digital DVB-C receiver

SONY BRAVIA:
Almost all models with letter indices D, S, W, X, V, E, Z and a diagonal size of 32 inches or more,
series:
3000/3500/4000/4020/4030/4050/4210/4500/4710/5300/5310/5500/5510/5600/5610/5710/5740

LOEWE:
Almost all models.

SHARP:
model: 46 (52, 65) XS1, LE700

PHILIPS:
series: **PFL****N

Toshiba:
series:
AV633/RV633/AV635/RV635/XV635/V635/SV685/LV685

JVC:
series: LT32DC1BH, LT26DC1BH

Panasonic:
series: TX-P42G10

LG Electronics:
Attention: it is necessary in the search menu: Country - include Sweden.
LCD TV series:
LH2000 DVB-T/MPEG-4/DVB-C
LH3000 DVB-T/MPEG-4/DVB-C
LH4000 DVB-T/MPEG-4/DVB-C
LH5000 DVB-T/MPEG-4/DVB-C
LH7000 DVB-T/MPEG-4/DVB-C
LU4000 DVB-T/MPEG-4/DVB-C
LU5000 DVB-T/MPEG-4/DVB-C
PLASMA TV series:
PS3000 DVB-T/MPEG-4/DVB-C
PS7000 DVB-T/MPEG-4/DVB-C
PS8000 DVB-T/MPEG-4/DVB-C
PQ200 DVB-T/MPEG-4/DVB-C
PQ300 DVB-T/MPEG-4/DVB-C
PQ600 DVB-T/MPEG-4/DVB-C

SAMSUNG:
Decoding of SAMSUNG TV models:

DVB-C receiver is built into all models starting from 2009! (letter index B, C or D)
Before setting up, you need to set the following parameters in the menu:
Country - Slovakia or Slovenia, Auto search for digital and analogue channels, Source - Cable, Network.

You can obtain more complete and accurate information on the presence or absence of a built-in digital receiver from sales consultants at the place where you purchased the TV!

Parameters for setting up a digital television test broadcast
(test broadcasting of digital television is available only for subscribers of the “Basic” package)

If there is no network search, then enter all frequencies manually.
Other frequencies: 642, 650, 658, 666, 674, 682, 690, 698, 706, 714, 722, 730, 738, 746, 754, 762, 770, 778, 786, 794, 802, 810 MHz.

Setting up digital channels on Toshiba branded TVs*


Now you can fully enjoy the capabilities of your TV by watching high definition channels. Enjoy watching and bright emotions!

Setting up digital channels on LG TVs*

1. In order to set up high-definition digital TV channels for the vast majority of LG models, press the “Menu” button on the remote control, you will see the TV menu in which you will need to select the “Options” section
2. Specify the country Finland or Germany
3. Now go to the “Settings” menu, “Auto search” and specify the method of connecting to the TV “Cable”
4. Now in the window that opens, go to “Settings” and enter the following parameters:
Search type fast
Frequency (kHz) 642000
Symbol speed 6875
Modulation 256
Network ID: auto
5. If you did everything correctly and saved all the changed parameters, then during the search you will find more than 100 digital channels and radio stations
6. An important feature of LG TVs is the “Automatic channel update” function. It must be disabled, otherwise the TV will periodically reset the channel list you have configured.
Go to “digital cable settings”:
Auto Channel Update: Off

*Your TV menu may differ from the model shown. In this case, you need to find tabs that are similar in meaning and enter the specified parameters

If it works, we are happy for you!

Setting up digital channels on Samsung TVs*

1. In order to set up digital TV channels for the vast majority of Samsung models, press the “Menu” button on the remote control. The TV menu will open, in which you will need to select the “Channel” section (Satellite dish icon). In the “Antenna” tab, specify the connection type as “Cable”. Go to the “Country” tab and select the “Other” option. The TV will ask for a pin code, if you have not changed it, you will see 0000
2. Go to “Auto Configuration”
Signal source: Cable,
You choose the type of channels at your discretion, you can find only digital channels or digital + analogue

3. Specify
Search mode: Fast
Net: Auto
Ident. Networks:-----------
Frequency: 642000 KHz
Modulation: 256 QAM
Transfer speed: 6875 KS/s

Click "Search"
4. As a result of the search, you should find approximately 100 television and radio channels.

*Your TV menu may differ from the model shown. In this case, you need to find tabs that are similar in meaning and enter the specified parameters

If it works, we are happy for you!
Now you can fully enjoy the capabilities of your TV by watching high definition channels. Enjoy watching and bright emotions!

Tuning digital channels on Philips TVs*

1. To tune in to high-definition digital TV channels on the vast majority of Philips models, press the “Menu” button on the remote control. The TV menu will open in which you will need to select the “Configuration” section
2. Select the Installation tab. After clicking OK, you will be taken to the second menu field, then go to the Channel Settings tab. After clicking the “OK” button, the third part of the menu will open, where you need to select “Automatic”. Installations". Next you will see a message about updating the channel list. Click "Get Started"
3. Select "Reinstall Channels"
4. In the “Country” section, you must select Finland. If this country is not in the proposed list, then select Germany
5. Since you are connecting to
digital television via the DVB-C cable network, you must select “Cable”
6. Before you start searching for channels, select "Settings" to manually adjust the search parameters
7. Set the baud rate to manual mode. In the tab, the transmission speed is manually changed from the control panel to 6875. In some TV models, the bit rate is indicated in the “Character 1”, “Character 2” tabs.
8. Now set the network frequency to manual mode and enter the network frequency 642.00 from the control panel
9. After clicking the “Done” tab, you will again be taken to the channel launch menu. Now you can start scanning.
10. If you did everything correctly and saved all the changed parameters, then during the search you will find more than 100 television and radio digital channels

General algorithms for setting up digital channels for various models of LCD TVs:

  1. Click on enter the menu (green button)
  2. Select in the menu - “Channel” (icon “Satellite dish”)
  3. Select - "Auto-tuning"
  4. Select - "Digital"
  5. Click - "Start"

First, we read the stickers on the back wall of the TV, where separately for each tuner (DVB-T and DVB-C) there is a list of countries in which, according to Philips, there is digital broadcasting (at the time the TV was released, but if you update the firmware through their official website, this list may change in subsequent firmware). If our country is not there, then we will have to put some other one from this list.

  1. Click on the icon - "House"
  2. Select - "Configuration"
  3. Select - "Install"
  4. Select - "Digital mode"
  5. Select - "Cable"
  6. Select - "Automatic"
  7. Click - "Start"

Setup takes approximately 5-10 minutes.

Philips TV models 2011

  1. Click on the icon - "House"
  2. Select - "Install"
  3. Select - "Search for channels"
  4. Select - "Reinstall channels"
  5. Select - “the country indicated on the sticker on the back panel” (usually France, Finland or Germany)
  6. Select digital mode – “Cable (DVB-C)”
  7. In the “Network frequency” line, enter the frequency 642.00 MHz
  8. In the line “Transmission speed” we enter 6875
  9. Next, select the line “Frequency scanning”

Setup takes approximately 5-10 minutes.

  1. Press the button - "Menu"
  2. Select from the menu - "Options"
  3. Select - "Auto-tuning"
  4. Select the country - "France, Switzerland, Sweden or Finland"
  5. Select the signal source - "Cable"
  6. Select - "Digital"
  7. Click - "Search"

Setup takes approximately 5-10 minutes.

If your TV model provides for the reception of digital channels, but does not have the “DTV MENU” item, then first select another country - France, Switzerland, Sweden or Finland.

  1. Press the button - "DTV"
  2. Click - "DTV MENU"
  3. Select - "Installation"
  4. Select - "Auto installation"
  5. Click - "OK"

Setup takes approximately 5-10 minutes.

Since not all SONY models are equipped with a digital tuner for cable TV (DVB-C), you need to check the model of your SONY TV.
Models equipped with a DVB-C tuner are marked KDL-**EX*** or KDL-**NX*** - for example KDL-32EX402R2. The first 3 letters in the model name (KDL) indicate that the TV is “digital”. In models KLV-**BX***, etc. There are no DVB tuners.

  1. Press the "MENU" button (for some models it is called "HOME" on the remote control (hereinafter referred to as the remote control). This button is usually blue
  2. Select "Settings"
  3. Find the “Digital Configuration” menu in the list of settings and enter it
  4. Select "Auto search for digital stations"
  5. A source selection window will open - select the TV connection type. Select "cable"
  6. In the selection of scan type - select the "full scan" mode
    6.1 Or select "Manual"
    6.2 Next, enter the frequency 642.000.
    6.3 Leave the access code as “Auto”. Next, enter the symbol rate 6.875.
  7. Click "get started"

Wait until the TV finishes searching for channels.
!!! Pay attention to the bottom of your TV's OSD menu. The bottom menu bar displays hints on which remote control buttons to perform certain actions in the TV menu.

Panasonic

  1. Press the button - "Menu"
  2. Select the item “Settings”
  3. In the window that appears, select “Analog settings menu”
  4. In the window that appears, select “Add TV signal”
  5. In the table that opens, put a tick on the “DVB-C” line and, going down below, click “Start auto-tuning”
  6. After searching for all digital channels, going to the main menu in the “Settings” item, the line “DVB-C setup menu” appears. By selecting this item, you can adjust the settings manually (set the frequency and speed)

If it works, we are happy for you!
Now you can fully enjoy the capabilities of your TV by watching high definition channels. Enjoy watching and bright emotions!

TV), it's time to move on to the most important part - setting up digital television. How to set up digital television yourself? Read more about this.

I will show the example of a receiver Mystery MMP-71DT2, and like me, his software is completely identical to Rolson. If you have a different console, the principle will be the same, but you may have to look at the instructions.

How to connect everything

First, let's connect antenna to the receiver, and the receiver to the TV. Preferably via an HDMI cable, so the image quality will be as clear as possible. If there is none, then through ordinary “tulips”, they usually come complete with the console. Look at the connectors in the instructions, you will get something like this. If the antenna has an amplifier, first turn it off, then you can always turn it on.

We launch all this equipment, set-top box, antenna, TV. Select the desired video input. If everything is done correctly, you will see a start menu like this:

How to set up digital television through “auto search”

By default, the set-top box is not configured for anything, and you yourself will need to catch the channels that are broadcast in your region. The easiest way is to run an auto search.

After launching the auto search, the set-top box will think for a long time, and should find something in the end. Important: since each one is transmitted at the same frequency, you will catch channels not one at a time, but in packs of ten at once. So be patient. If in analog TV channels are caught one at a time, then a few minutes may pass, and the set-top box will search. But then all 10-20 channels will pop up immediately.

After the search is over, the set-top box will prompt you to add the found channels. If you find all 20 pieces, congratulations, the process is complete!

List of tuned channels, TV Guide function

How to check signal quality when setting up digital TV

Check that the signal is strong enough and everything is set up well.

It's very easy to do. You should have an INFO button on your set-top box; pressing it three times displays data on the quality and intensity of the signal. Look in the instructions, it may be called differently, but it will do the same thing:

The higher the signal, the better. Optimal - from 60% onwards

If both indicators are high, above 60%, everything is fine.

Check on both multiplexes, say, on Channel One and TNT.

Since different multiplexes are transmitted, you can catch the first one well, and the second one poorly, or vice versa. Your task is to rotate the antenna so that both are caught well.

But in practice it happens a little differently. For example, you can catch duplicates. When identical channels will occupy several places at once. It doesn't seem critical, but it's annoying. How to treat, I.

What to do if you caught duplicates or didn’t catch anything

The second option is when not everything was caught, or nothing was caught. Fine tuning and manual mode will help us here. We read about it. However, if you live in a city and there are towers near you, then in 90% of cases an automatic search is enough for you.

To sum it up

As you can see, setting up dvb t2 digital television with your own hands is not a difficult task. And you certainly shouldn’t call a specialist who will do the same thing for you for a thousand rubles)