How to set your wristwatch? Electronic desk clock alarm clock with temperature measurement function.

Can't learn to wake up with an alarm? No problem, you just need the “right” alarm clock that will wake up even the most inveterate sleeper by all means! Now, in order to turn off the signal of your alarm clock, you won’t just have to reach out to the treasured button, but you will need to first catch this nimble and annoying “wake-up caller”. Clocky's running alarm clock will not let you sleep through any important event in your life!

Nutrition

The alarm clock requires four AAA batteries to operate. It is enough to insert them into a special compartment as shown in the figure below, close the compartment with a screwdriver, and your alarm clock is ready for use.

Setting the time

To enter the time setting mode, simply press the “t” key on the control panel. Consecutively pressing the “h” and “m” buttons will allow you to set the desired number of hours and minutes.

Setting an alarm

Enter the alarm setting mode by pressing the “a” key on the control panel. Pressing the “h” and “m” buttons in succession will allow you to set the desired number of hours and minutes for your alarm.

Setting the time range for repeating signals

To enter this mode, you must press the “a” button twice, after which you can, by repeatedly pressing the “m” button, set the signal repeat time range from 0 to 9 minutes.

Setting the alarm time

To enter the mode for setting the alarm time, you must press the “t” button on the control panel twice, after which the clock display will display the number 1 - the initial setting. Press the h button repeatedly to select a value from 1 to 5, then press the t button to confirm the value.

When you select the value “1”, the alarm will continue to move for 20 seconds
When you select the value “2”, the alarm will continue to move for 40 seconds
When you select the value “3”, the alarm will continue to move for 60 seconds
When you select the value “4”, the alarm will continue to move for 80 seconds
When you select the value “5”, the alarm will continue to move for 100 seconds

If, when you first sound, your alarm clock only plays sound, but does not move, do not worry. A minute after pressing the “end call” button located on the cover of the device, it will begin to drive and at the same time give a signal, finally waking up the person who turned it off.

Demo mode

Press the "t" key twice until a number from 1 to 5 appears (alarm wheel rotation mode), select any value from 1 to 5 using the "h" button, then press the "t" button twice. The alarm clock will start sounding immediately. To turn off the demo mode, press the button with the image of a wheel on the front panel of the alarm clock.

Don't let yourself oversleep a single significant event or meeting in your life! Order Clocky's running alarm clock right now!

When buying chronographs abroad, owners are faced with the question of how to set the time on an electronic watch. The operating instructions for them are written in a foreign language, so sometimes it is difficult to understand the settings. Standard digital watches have only two buttons for settings "MOD" And "SET". The first one is used to switch setting modes, i.e. date, time, alarm clock and more. The second is responsible for changing parameters and saving them.

Settings

How to set the time on an electronic clock using the MOD and SET buttons:

Hold MOD for a short time. The field being edited will begin to blink. If several fields are blinking at once, with one click on MOD you can switch to the required field.
Using SET we set the necessary parameters. The values can be changed by pressing the button multiple times.
Using MOD, switch to the next field and also using SET, change the values to the required parameters.
Once completed, press MOD to exit settings mode.

This instruction is about how to set up a digital watch with 2 buttons. However, there are cases when additional buttons are installed on digital devices. Usually on such watches they serve as a value switch up and down. How to set up an electronic clock in this case? Much simpler:

Use the steps above.
After pressing MOD you will switch between modes.
After moving to another field, press SET to begin changing parameters.
By pressing additional buttons on the other side of the watch, change the values. The top button increases the number, the bottom button decreases.
When finished, press SET and switch mode. When you are finished changing the settings, press MOD to exit.

How to turn on and off the alarm on an electronic watch?

How to turn off an alarm on an electronic watch? This function is designated “ALARM” on the watch. In order to enable or disable it, you need to use the MOD button to find a field with such an inscription and use SET to change the set value. OFF – turn off, ON – turn on.

The overwhelming majority of modern watch models are produced abroad. To get a quality product, people order devices from the most famous companies. Electronic wristwatches have enormous functionality, but rarely all this functionality is localized, which leads to setup difficulties. The language barrier leads to a dead end, since not every user has knowledge of the English language. How to set up an electronic clock yourself? It's not as complicated as you might think. Now you will see this.

Settings

Most often, models are equipped with MOD and SET keys. To set the time on such a watch, you need to do the following:

Hold down the MOD key for a while. The edit field should start flashing. If several interface fields start blinking at once, press the same key once to switch to the desired field.
Use the SET button to set the desired parameters. To change the values, you need to press this button repeatedly.
Use the MOD key again and switch to other fields. Again use another button to change parameter values.
If the desired values have been set, then complete the entire procedure with the last click on MOD.

Everything seems simple, but how to set up an electronic watch with 4 buttons? This procedure looks even simpler.

Important! When you've figured out the settings, it's time to think about your harmonious look with a new accessory. Find out all about:

Four buttons on a gadget

If your gadget is equipped with four buttons, then the entire setup process will look even simpler:

You need to also click on the MOD button. When you make the numbers on the device screen blink, press SET once, and then scroll through one of the other two buttons.
The first key is responsible for increasing the value, and the second is responsible for decreasing it.
If you have set the parameters, press the MOD key again.

There are accessories that have even more keys. What should the user do in this case?

Setting up devices with even more controls

But in this case, there is no objective instruction. It is best to follow the recommendations described in the accompanying documentation. Often additional keys are responsible for calling up an electronic thermometer, calendar, timer or stopwatch.

Important! Such keys simply visualize parameters, but do not configure them in any way.

If you still don’t want to use the standard documentation, you can try making a few presses on the MOD key, scrolling through all the functions. When you find the option you want, place your finger on the SET key and set the data. Typically, almost all electronic devices are configured in this way.

Important! Bookmark useful articles for the future, the information from which will definitely be useful to you in the future:

Now you understand how to set the time on an electronic watch, but how to set an alarm on it?

Set the alarm clock

Absolutely all models of electronic devices are equipped with an alarm function. In order to start it, you need to press “MOD” again until you find the inscription “alarm” on the display.

Important! The alarm time is set in the same way as setting the time and date, which was described above. The “SET” control element in this field is responsible for turning this function on and off.

In fact, different devices are configured differently, so the surest way to parameterize is to type the model name into any popular search engine. On the Internet you can easily find any localized instructions for setting the time.

You can also use the services of the store where the device was purchased. Just bring the device to a consultant and ask for help.

Important! Setting the time in stores is completely free, you can ask the seller absolutely any questions about your equipment.

Video material

Now get started, because they are extremely simple and in a matter of minutes you can set the necessary settings on your accessory.

Electronic desk clock alarm clock with temperature measurement function

LCT047

GETTING STARTED

1. Open the battery compartment.

2. Insert 3 new AAA batteries according to the correct polarity.

3. Close the battery compartment.

4. Once the batteries are inserted, the LCD display will light up. The default time is 02:00.

Attention:

If the display does not light up, try changing the batteries or pressing the button RESET.

CLOCK SETTING BUTTONS

SNOOZE / LIGHT– press this button to turn off the ringing alarm. In any mode, press this button to turn on the clock backlight for 5 seconds.

MODE– press this button to switch from normal mode to alarm mode and back.

ALM ON/ OFF– In normal/alarm mode, press this button to turn on/off the alarm/alarm snooze mode.

ADJ- In normal mode, press this button to move to date/month/year. In setting mode, press this button to change the setting value.

°С/°F– press this button to select the temperature display format.

RESET– Click this button to reset all settings. If there are errors in the clock operation, you need to reset all settings and reset the clock.

CHARACTERISTICS

1. Alarm snooze/backlight button ( SNOOZE / LIGHT)

2. LCD display

3. Mode switch button ( MODE)

4. Alarm on/off button ( ALM ON/ OFF)

5. Set button ( ADJ)

6. Temperature mode format selection button °С/°F

7. Button RESET(reset)

8. Battery compartment cover

9. Stand

Arrangement of symbols on the display

Normal mode

4. Day of the week

5. Temperature

Alarm mode

1. Alarm time

2. Alarm icon

3. Alarm mode

4. Alarm snooze icon

SETTING THE TIME AND CALENDAR

1. In normal mode, press and hold the button for 3 seconds ALM ON/ OFF

2. Press the button ADJ

3. Repeat the above operation to set HOURS - MINUTES - SECONDS - 12/24 MODE - YEAR - MONTH - DATE.

SETTING THE ALARM

1. In normal mode, press the button ALM ON/ OFF once to turn on the alarm, the icon will light up « "; twice – the alarm repeat mode will turn on ( SNOOZE), the “ Zz"; three times – both the alarm clock and the snooze mode will turn on.

2. In normal mode, press the button MODE to set the alarm time.

3. Press and hold the button for 3 seconds MODE. The hour number will start flashing.

4. Press the button ADJ to set the correct value.

5. Repeat the above operation to set the minutes.

Attention:

1. After turning on the snooze function, the alarm will ring 5 times within 60 seconds with a 5-minute break.

2. Press the button SNOOZE / LIGHT to stop the alarm from ringing and switch to snooze mode. Press the button if you want to not only stop the alarm from ringing, but also turn it off completely.

REPLACING BATTERIES

When the symbols on the display become dim, you need to replace the batteries - 3 pcs. type AAA.

ATTENTION!

Please dispose of used batteries in an environmentally friendly manner.

Settings

How to set the time on an electronic clock using the MOD and SET buttons:

Hold MOD for a short time. The field being edited will begin to blink. If several fields are blinking at once, with one click on MOD you can switch to the required field.
Using SET we set the necessary parameters. The values can be changed by pressing the button multiple times.
Using MOD, switch to the next field and also using SET, change the values to the required parameters.
Once completed, press MOD to exit settings mode.

Use the steps above.
After pressing MOD you will switch between modes.
After moving to another field, press SET to begin changing parameters.
By pressing additional buttons on the other side of the watch, change the values. The top button increases the number, the bottom button decreases.
When finished, press SET and switch mode. When you are finished changing the settings, press MOD to exit.

How to turn on and off the alarm on an electronic watch?

Slap watch "Pulse"

Water protection

Caring for your watch

1. Clock (hour, minutes, seconds) and date
2. Stopwatch
3. Alarm clock

Button "B" switches between editable parameters. The numbers are changed using the "C" and "D" buttons. Go back to the current mode - button "B".

Setting the time and date:

In time display mode, press button "B" 3 times, then use buttons "C" and "D" to set the current time and date. To return to normal mode from the setup mode, press the "B" button.

Select between 12/24 hour time display - button "D"

Stopwatch:

In normal time display mode, press button "B" 2 times, start the stopwatch with button "D", stop the stopwatch with button "D". Reset the stopwatch: after it stops, press the "C" button.

Alarm:

In the time display mode, press the “B” button once, then use the “C” and “D” buttons to set the hours and minutes. When the alarm clock is activated, the alarm clock symbol will appear on the clock dial. To turn off the alarm, press the "B" button once, then press the "D" button. The alarm symbol should disappear from the watch dial.

To return to normal mode from the setup mode, press the "B" button.

Backlight:

Button "A" turns on the backlight of the clock dial. The backlight is active when the "A" button is pressed and held. If you do not press any button within three seconds, the clock backlight will automatically go out.

Watch "Fast sport"

Battery

Water protection

Caring for your watch

When you are not using your watch, store it in a dry place.
The chemical reactions caused by these materials cause damage to the gaskets, case and polish of the watch display.

Turning on the clock
The clock is turned on by pressing any of the three buttons once ("A", "C", "D"). By pressing Button "A" you can switch between modes in the "Current mode" in the following sequence:
- time (hours, minutes)
- date (month, day)
- seconds
Setting the clock
In the "Current mode" press the "B" button - the parameter being edited will begin to blink and you need to use the "A" button to set the desired position of the numbers. Next, use the “B” button to select the appropriate parameter and continue editing with the “A” button.
The clock display is configured in the following sequence:
1. Clock (1-24)
2. Minutes (01-60)
3. Month (1-12)
4. Day (1-31)
5. year (00-99)
6. Time system (12 or 24 hour)

Watch "Electronic sports"

In the "Clock" mode you can edit:
- seconds
- watch
- minutes
- year (in the current mode this parameter is displayed as the day of the week)
- month
- date
The transition between 12 and 24-hour time systems is carried out with the LIGHT/RES button.

In the "Alarm clock" mode the following can be edited:
- watch
- minutes
- month
- date

In the "Additional hours" mode the following can be edited:
- watch
- minutes
In this mode, an additional time is configured, above which the main time will always be displayed.
In the "Timer" mode you can edit:
- seconds
- minutes
- seconds
The transition between the "AUTO" and "MANUAL" modes is carried out with the LIGHT/RES button.
In Stopwatch mode:
Start and stop - ST-STOP button, reset - LIGHT/RES button.

Watch "Future"

Turning on the clock
The watch is turned on by pressing either of the two buttons once. Button "A" turns on the animated backlight of the clock, button "B" turns on the usual static backlight. By pressing the "A" button, the "Current mode" switches between modes in the following sequence:
- time (hours and minutes) - P
- date (month and day) - D
- day of the week - W
Setting the clock
The display is configured by successively pressing the “B” button and then the “A” button.
There are two ways to switch to editing mode:
Option 1. Press the top, then the bottom button.
Option 2. Press the bottom button twice.
The parameter being edited will begin to blink and you need to use the “A” button to set the desired position of the numbers. Next, use the “B” button to select the appropriate parameter and continue editing with the “A” button.
:
1. Hours (1-12)
2. Minutes (05-60 in 5 minute increments, four square dots in the center of the clock display will be used to set 6, 7, 8, 9 minutes)
3. Month D (1-12)
4. Day D (1-31)
5. Day of the week W (1-7)
6. Display backlight brightness (4 levels): adjustable by selecting the number of square dots
7. Display backlight time 60 (05-60 seconds)
If you do not press any button within five seconds When a value is flashing, the clock backlight automatically goes out. The screen turns off automatically after a specified time interval (05-60 seconds in 5 second increments).

Watch "Leg"

Battery
The battery in the watch you purchase is factory installed and should be replaced at the first sign of power failure.
Water protection
The watch is not protected from water. Avoid exposure to any moisture.
Caring for your watch
Never attempt to open the case or remove the back cover.
The rubber gasket that protects the watch from water and dust should be replaced every 2-3 years.
If moisture gets inside your watch, have it checked immediately by your nearest workshop.
Do not expose your watch to extreme temperatures.
Although the watch is designed to withstand normal use, you should avoid rough handling or dropping it.
Do not fasten the strap too tightly. Between your wrist and the strap should go through your finger.
To clean the strap, use a dry, soft cloth, or a soft cloth moistened with a mild, neutral detergent and water solution. Never use products that evaporate easily (eg benzene, solvents, spray cleaners, etc.).
When you are not using your watch, store it in a dry place.
Avoid contact of the watch with gasoline, cleaning solvents, spray aerosols, adhesives, paint, etc.). The chemical reactions caused by these materials cause damage to the gaskets, case and polish of the watch display.
The clock is turned on by lightly touching the display:
1 time - time (hours, minutes)
2 times - date (month, day)
3 times - seconds
Setting the clock
1. Lightly touch the display to enter the “Current time” mode.
2. Touch and hold your finger in the center of the display - the parameter being edited will begin to blink. Now you need to change the numbers with light touches. Next, use repeated long touches of the display to switch from mode to mode and continue editing with light, short touches.
:
1. Hours (1-12, A-am or P-pm)
2. Minutes (00-60)
3. Y (00-100)
4. Month D (1-12)
5. Day D (1-31)
(do not touch the display), the clock automatically returns to the “Current Time” mode and the blinking stops.
If you do not press any button within five seconds When a value is flashing, the clock backlight automatically goes out.

Watch "Original"

When you are not using your watch, store it in a dry place.
Avoid contact of the watch with gasoline, cleaning solvents, spray aerosols, adhesives, paint, etc.).

Turning on the clock
The watch is turned on by pressing either of the two buttons once. By pressing the "A" button, the "Current mode" switches between time (hours, minutes) and date (month, day).
Setting the clock
Press button "A" to switch from mode to mode:
1. Current time mode
2. Date mode
Setting the time on the digital display:
1. Press the "A" or "B" button to enter the "Clock Time" mode, then press and hold the "B" button in the "Current Time" mode until the hour value flashes.
2. Use the "B" button to move between sections in the following sequence:
- watch
- minutes
- month
- date
3. Press button "A" to move the flashing value from digit to digit to set the desired position of the digits.
If you do not press any button within five seconds When a value is flashing, the clock backlight automatically goes out.

Watch "Touch"

Battery
The battery in the watch you purchase is factory installed and should be replaced at the first sign of power failure.
Water protection
The watch is not protected from water. Avoid exposure to any moisture.
Caring for your watch
Never attempt to open the case or remove the back cover.
The rubber gasket that protects the watch from water and dust should be replaced every 2-3 years.
If moisture gets inside your watch, have it checked immediately by your nearest workshop.
Do not expose your watch to extreme temperatures.
Although the watch is designed to withstand normal use, you should avoid rough handling or dropping it.
Do not fasten the strap too tightly. Between your wrist and the strap should go through your finger.
To clean the strap, use a dry, soft cloth, or a soft cloth moistened with a mild, neutral detergent and water solution. Never use products that evaporate easily (eg benzine, solvents, spray cleaners, etc.).
When you are not using your watch, store it in a dry place.
Avoid contact of the watch with gasoline, cleaning solvents, spray aerosols, adhesives, paint, etc.).
Turning on the clock
The watch turns on by lightly touching the display once. By touching again, the “Current mode” switches between time (hours, minutes), date (month, day), seconds.
- time (hours/minutes)
- date (month/year)
- seconds
Setting the clock
1. Lightly touch the display to enter the “Current Time” mode.
2. Touch the right side of the display near “SET” to enter “Edit Mode”. The parameter being edited will start flashing. Now, lightly touch the left side of the display near “MODE” to change the numbers.
3. Next, by repeatedly touching the right side of the display near “SET,” you can switch from mode to mode. Editing continues with light touches or a continuous touch on the left side of the display near "MODE".
The clock display is configured in the following sequence:
1. Clock (1-12/1-24)
2. Minutes (00-60)
3. Month (1-12)
4. Day (1-31)
5. Year (2001-2099)
6. 12 or 24 hour time display system
If you make no changes in edit mode(do not touch the display), the clock automatically turns off.
If you do not touch your watch within three seconds, they automatically go out.

Clock "Data"

1. Clock (hour, minutes and seconds)
2. Stopwatch
3. Alarm clock
4. Date

The MODE button switches between edited parameters. The numbers are changed using the ST/SP and RESET buttons. Go back to the current mode - MODE button.

Setting the time and date:

In time display mode, press the "MODE" button 3 times, then use the "RESET" and "ST/SP" buttons to set the hours and minutes. By pressing the "RESET" button again, you enter the mode for setting the current date and day of the week. You can view the date in the current mode by pressing the "ST/SP" button.

Electronic watches are a stylish and practical accessory for daily use. The easiest way to set them up is usually contained in the instructions that came with the device upon purchase. If it is missing, you can search for documentation on the manufacturer’s official website, or use our recommendations outlined below.

How to set up an electronic clock - buttons

In this case, by electronic watch we will mean a device equipped with an LCD display that can work with programmable data display. For example, consider a watch from the popular brand CASIO, known all over the world. Almost all electronic devices of this type are controlled by buttons, the operation of which is worth devoting a separate paragraph to. These elements can respond to pressing:

launching settings;
switch modes;
turning on or off both the clock itself and individual functions;
resetting previously installed settings.

Configuration is easy to start by one-time or multiple clicks on one or several buttons at the same time, sequential clicks or “drowning” with a delay. Pressing and holding is just typical for CASIO electronic watches, opening a list of settings. Then you can select the time, time zone, date, timer, sound signal, and so on. The duration of pressing can vary from 2 to 7 seconds, depending on the model. The same principle applies to the button to turn on the backlight.

How to set up an electronic clock - functions of an electronic clock using the example of CASIO DW-6900

This accessory is equipped with one front and four end buttons. Among them:

ADJUST (responsible for entering the settings and is located at the top left, recessed);
MODE (changes modes, located at the bottom left, the rest of the buttons are protruding);
SPLIT/RESET (performs the “Split” and “Reset” functions, respectively, located at the top right);
START/STOP (starts the “Start” or “Reset” functions, for example for a timer, located at the bottom right);
LIGHT (lower, front button that starts the backlight).

The entrance to the general settings does not open from any menu, but only from the current time mode (in fact, the most “normal” state of the watch, with the display of time, date and other service icons). When the ADJUST button is pressed, wait for the second digits to blink and begin setting, changing the values using the buttons described above.

How to set up an electronic clock - setting the time

To understand in practice how to control an electronic clock, let's consider the process of changing the time, for convenience, designating the upper left button with the letter A, the upper right - B, the lower left - C, the lower right - D. Next:

Hold A until the seconds blink.
Press C several times to select daylight saving time, hour, minute, etc.
When the desired value is flashing, it is ready to be adjusted.
Press D to reset the counter to zero if the current values are between the numbers 30-59. This may be true - with values from 0 to 29 the counter will not reset to zero; you will have to add or subtract it manually.
Pressing D once will cause the number to increase, B will cause it to decrease.
When the correct value is set, press A to complete.

If your watch has regular hands, they should automatically sync with the electronic values. When this does not happen, press C and use it to scroll to the “H-S” function. Long press and hold A, waiting for the numbers to blink over time, then use D to adjust the arrows. Save the changes with button A.

Expensive watches always look respectable and prestigious. The accessory emphasizes the status of a person and, moreover, it is very convenient, since you do not have to ask strangers for the exact time.

But even the most expensive and popular models can sometimes fail, so it is necessary to carry out the correct setup immediately. To learn about this process, you can use step-by-step instructions, using the one that came with the watch.

Keys

It is known that many models of accessories have special keys that help you quickly and conveniently set the time yourself. This is no exception for the Casio brand.

So, on the watch you can find the following buttons:

mode. This key helps to configure all the necessary modes;
forward. Using this button, the arrows are adjusted by pressing forward;
adjust. Installation in progress.
reserve. If you need extra lighting, this key will definitely help you.

All these buttons are marked with letters, which will help you understand the correct installation.

Setup step by step

The first thing to do is set the time. When you press a key, different modes and beeps appear to indicate the transition from one function to another.

It is necessary to select the setting item, and then determine the exact match of the time using the arrows and the electronic indicator. If the numbers do not match, you need to use the adjustment key.

After this action, the hands will be at the twelve o'clock position. If this does not help, you will have to turn to manual mode using the adjustment and backlight key.

When the hands take the desired position in accordance with the time, you must press the set button.

The next step is the electronic indicator. To do this, you need to use the installation key again.

Location options appear on the segment. After this, it is best to use the instructions that came with the watch.
All the necessary settings will be indicated there, which will help set the correct parameters for a particular locality. After this, use the all modes control key.

If necessary, you need to deactivate the automatic setting and switching function.

After this, you must select the format in which the time is displayed.

How to set up your Casio watch, watch the video:

Electronic desk clock alarm clock with temperature measurement function

LCT047

GETTING STARTED

1. Open the battery compartment.

2. Insert 3 new AAA batteries according to the correct polarity.

3. Close the battery compartment.

4. Once the batteries are inserted, the LCD display will light up. The default time is 02:00.

Attention:

If the display does not light up, try changing the batteries or pressing the button RESET.

CLOCK SETTING BUTTONS

SNOOZE / LIGHT– press this button to turn off the ringing alarm. In any mode, press this button to turn on the clock backlight for 5 seconds.

MODE– press this button to switch from normal mode to alarm mode and back.

ALM ON/ OFF– In normal/alarm mode, press this button to turn on/off the alarm/alarm snooze mode.

ADJ- In normal mode, press this button to move to date/month/year. In setting mode, press this button to change the setting value.

°С/°F– press this button to select the temperature display format.

RESET– Click this button to reset all settings. If there are errors in the clock operation, you need to reset all settings and reset the clock.

CHARACTERISTICS

1. Alarm snooze/backlight button ( SNOOZE / LIGHT)

2. LCD display

3. Mode switch button ( MODE)

4. Alarm on/off button ( ALM ON/ OFF)

5. Set button ( ADJ)

6. Temperature mode format selection button °С/°F

7. Button RESET(reset)

8. Battery compartment cover

9. Stand

Arrangement of symbols on the display

Normal mode

4. Day of the week

5. Temperature

Alarm mode

1. Alarm time

2. Alarm icon

3. Alarm mode

4. Alarm snooze icon

SETTING THE TIME AND CALENDAR

1. In normal mode, press and hold the button for 3 seconds ALM ON/ OFF

2. Press the button ADJ

3. Repeat the above operation to set HOURS - MINUTES - SECONDS - 12/24 MODE - YEAR - MONTH - DATE.

SETTING THE ALARM

2. In normal mode, press the button MODE to set the alarm time.

3. Press and hold the button for 3 seconds MODE. The hour number will start flashing.

4. Press the button ADJ to set the correct value.

5. Repeat the above operation to set the minutes.

Attention:

1. After turning on the snooze function, the alarm will ring 5 times within 60 seconds with a 5-minute break.

REPLACING BATTERIES

When the symbols on the display become dim, you need to replace the batteries - 3 pcs. type AAA.

ATTENTION!

Please dispose of used batteries in an environmentally friendly manner.