Geometric dimensions of the average Mishin coil. Mishina's Healing Coil: Manufacturing and Settings

The optimal ratio of internal diameter to external diameter is 1/3
- Large flat coil - internal D - 70-80 mm, external - 240 mm, SHTLP-4 wire two cores.
- Flat coil 120-130 mm. internal D - 40mm, external - 120 mm, wire 0.5mm varnish. Optimal operating frequencies are 270-330 kHz.

How to make a Mishin coil with your own hands

Scheme for manufacturing a flat coil. D - 120-130 mm.

• 1. We start making a flat Mishin coil from the base. We make a base onto which we glue double-sided tape.
• 2. In the center of the base we install a round protrusion with a diameter of approximately 40 mm.
• 3. Take a varnished wire 0.5 mm in diameter and 10-12 meters long.
• 4. Around the round protrusion you need to wind two wires at once parallel to the plane of the base.
• 5. After manufacturing the coil, it is necessary to determine the frequency of operation of this container:

We make two taps from the coil. We take the end of one wire from the inside of the coil and the second from the other wire from the outside. In this case, the circuit remains open, and the two unused outputs of the plates are simply cut off.

Option 2

The flat coil works on minor problems such as viruses and fungal diseases. It can quickly remove scar tissue and speed up healing.

Manufacturing diagram of a large flat coil 250 mm

Option 1 (when using a standard generator with a power of up to two watts)

We connect the oscilloscope probe in parallel to the generator terminals.

We gradually increase the frequency of the generator and look for the first frequency at which the output voltage of the generator is the lowest. This will be the operating frequency of this capacitance.

Option 2

We connect a resistor with a voltage of 1 Ohm in series in the power circuit.

We are looking for the first largest amplitude value.

Option 3 (if you don’t have an oscilloscope)

We make a flat inductor, the load of which includes 2 counter LEDs.

We look for the frequency based on the maximum luminosity of the LEDs.

For the above capacitance design, the approximate frequency is 280-320 kHz. In this case, the effective power range lies within ±10 kHz relative to the operating frequency.

A large flat coil allows you to work effectively at the level of the central nervous system, eliminate circulatory problems and many other small vortex problems of living organisms.

Scheme for manufacturing a toroidal coil (torus)

We make two taps from the coil: we take the end of one wire from inside the coil and the second from another wire outside. In this case, the circuit remains open, and the two unused outputs of the plates are simply cut off.

Option 1 (when using a standard generator with a power of up to two watts)

We connect the oscilloscope probe in parallel to the generator terminals.

We gradually increase the frequency of the generator and look for the first frequency at which the output voltage of the generator is the lowest. This will be the operating frequency of this capacitance.

Option 2

We connect a resistor with a voltage of 1 Ohm in series in the power circuit.

We are looking for the first largest amplitude value.

Option 3 (if you don’t have an oscilloscope)

We make a flat inductor, the load of which includes 2 counter LEDs.

We look for the frequency based on the maximum luminosity of the LEDs.

For the above capacitance design, the approximate frequency is 280-320 kHz. In this case, the effective power range lies within ±10 kHz relative to the operating frequency.

The toroidal coil copes well with crystalline slags such as stones and sand. Thor also eliminates pain symptoms and works well with wound healing.

- A strange remedy from the category of vortex medicine

Advantages: many positive reviews

Disadvantages: price

What is it like?

This is an electronic device that, according to doctors, can heal various human diseases.

Moreover, he himself selects problem areas and begins to treat them, i.e., as it were, the most dangerous place in the human body. Therefore, it is not even necessary to apply it, as doctors say.

The kit includes a generator with a field indicator, a power supply for connecting to the network, a flat coil with copper wire, a donut (torus), and instructions for use. All this pleasure cost me 5,600 rubles. I ordered online.

This entire design was developed by specialist Alexander Mishin. The coil operates at a frequency of 285 kHz, and the waveform is sine. In general, this doesn’t tell me anything, so I turned to the doctors, who explained everything in detail about the benefits of this unit.

According to them, this device can act on any problem areas in a living organism. Moreover, this may not necessarily be a person. Experiments were also carried out on animals and there, too, excellent rates of healing from their diseases were obtained.

As they say, a vortex flow of energy is used here. It acts on your problem and in some ways its effect can be compared with the use of antibiotics, which, as we know, can cause harm to some organs, but this remedy supposedly has no such contraindications.

Moreover, with the help of this device it is possible to treat various oncological diseases without surgery. There will be no need for radiation therapy. After all, vortex rays also work here, but they are not as dangerous as the generally accepted methods of fighting cancer.

Among other things, these vortex flows are capable of restoring damaged nerve cells. After all, we all know that they cannot be restored, but with the help of this unit we can try to restore it.

Doctors advise using this remedy in doses. Do not use it for too long or apply it to your body. 5 minutes to 1 hour is enough. And this way you can conduct sessions every day.

It is quite lightweight and easy to use.

Doctors recommend starting treatment from the lumbar region, since this coil is capable of removing many toxins from the body, which means your kidneys will do this. This means it needs to be applied to the kidneys. That is, first rid the body of toxic compounds, and then begin to further improve your health.

Of course, it all depends on the person’s obesity. If you are fat, then it will not work on you so quickly, so you need to keep it longer, but a thin person can do less. But you yourself will feel in your body how long you need to keep it in order to have an effect.

Then you can work on your limbs if your arms or legs hurt. It should be applied to problem areas. For these places, not a coil, but a torus will be used. It is convenient to hold it there and it will cover the entire desired surface.

Many people try to construct such coils and tori themselves. But still doctors do not recommend this. After all, there are many nuances in this process. If you are not well versed in vortex medicine, then you can only harm your body.

On YouTube you can find many ways of craftsmen who make them, but this should still be done by specialists with the necessary education.

On the Internet you can find many reviews about the positive effects of this coil on your body. I have just acquired this pleasure, so I haven’t noticed anything positive in my body yet, but perhaps it just takes time.

In any case, all the people whose opinions I have heard praise this miracle. If it doesn't help, at least it won't harm.

Before use, be sure to consult a specialist

Video review

All(5)

Mishina reels - Customer reviews!

Video instruction - Mishina TGS-3A coils

Mishina's reel! reviews!!!

Experiment with a mouse. Mishin coils.

Doctor about Coils Mishina Tesla

For more than a century, humanity has been widely using electricity. Countless devices of all kinds have been produced. At the same time, no one thinks about their safety.

Over the past decades, the number of pathologies of the human body, the treatment of which cannot be treated by medicine, has increased. The reason is often not so much a poor environmental situation as a lack of understanding of the processes in all devices that operate on the basis of the phenomenon of electromagnetism.

If we touch upon physical processes, then in nature they proceed in accordance with In simple terms, performing an action is impossible without a fulcrum, and during its execution, the object and the support receive equal mechanical influence. If you look at this problem through the prism of vortex processes, it turns out that when creating electromagnetic radiation, the electrostatic plane is taken as a basis.

The Mishin healing coil, reviews of which indicate that it has a high degree of functionality, provides vortex processes. They have a healing effect.

What does electricity radiation destroy?

Our life is full of continuous pulsations emanating from electrical devices. They have a destructive effect at the molecular level. As a result, increased energy saturation of molecules is caused, which leads to the formation of large clusters. Many looped structures of molecules in the human body cannot be treated with medications due to their high level of strength. Such formations in the body lead to the appearance of cancer or block any functions in the body.

The most unified method is to create a zone with a reduced density of the medium using electrostatic implosive resonance. This effect is provided by the Mishin healing coil.

The essence of her work is actually built on gravity. True, the range of the device is small. It is only 2-3 meters. The level of transmitted power of such equipment depends on the degree of voltage. The amplifier for the Mishin coil has an output voltage frequency of 12-24 volts. The current indicator should not exceed 100-200mA.

Principles of flat coil manufacturing (DMA)

How to make such a device as a Mishin coil with your own hands? A preliminary preparation of a base is required, on which double-sided tape should be glued. A round protrusion is installed in the center. Its diameter is 25 mm. Around it, the laying of two wires begins, which should lie parallel to the plane of the base.

The generator for the Mishin treatment coil can be of a standard configuration. Its power is quite enough for health purposes. The generator circuit for the Mishin coil is presented below.

After manufacturing such a device, a container is obtained based on a pair of spiral-shaped plates that are nested inside each other. It is possible to use any copper wire, the diameter of which, together with the insulation, will be no more than 1.5 mm. The diameter of the coil should not be more than 23-25 ​​cm. The wire is fixed at the top. You can secure it with tape.

The Mishin coil, the circuit of which is not so complicated, can easily be assembled independently. The materials for its manufacture are easy to obtain at any electrical appliance store.

How to set up a coil using an oscilloscope?

Mishin's vortex coil needs to determine the frequency. For this purpose, a pair of taps are made from the device. You should take the end of one wire from the inside of the coil, and the other end from the outside. In this case, the circuit remains open, and the two terminals of the unused plates should be cut off.

When using a standard type generator with a power of 2 W, it is possible to determine the operating frequency of the device by connecting an oscilloscope probe in parallel with the generator terminals. while gradually increasing. The first frequency at which the generator output voltage is lower is determined. This will be an indicator of the operating frequency of this device.

Second voltage measurement option

The device can also be measured using a 10 m resistor, which is connected in series. The highest amplitude value should be determined. This method makes it possible to evaluate the quality level of the supplied sine wave in load mode in the tank.

How to configure using the LED indicator?

The operating frequency of the capacitance can be determined using an indicator coil. It is an induction device that includes two counter LEDs.

With this method, you can find the frequency by the maximum luminosity of the LEDs. In this case, the generator voltage decreases. This ensures a reduction in the frequency range at which the glow is observed.

Effective coil frequency indicator

If you ensure that the wire is firmly fastened and the device is not subjected to severe mechanical deformation, then after setting the optimal power supply frequency to the container, its frequency indicator will not change during use. For the capacitance design presented above, the average frequency is 310 kHz. In this case, the effective frequency range of the supply signal lies within ±10 kHz relative to the operating frequency.

Such a device has a wide electrostatic spectrum and a low gradient of plane change towards the center of the device during operation. This will allow you to effectively influence the central nervous system, eliminate circulatory disorders and many other vortex problems in the body.

Design features of a flat coil with a diameter of 12 cm

Mishin treatment coils with a reduced distance between the plates have a higher level of impact on pathogenic formations. For example, you can use a wire with a cross-section of 0.5 mm in varnish insulation. The length of each wire will be 10-12 meters.

The internal diameter will also be approximately 25 mm, and the external one - 130 mm. This capacity has a high level of efficiency. It can affect the smallest viruses, fungi, eliminate scars and accelerate the process of tissue regeneration.

Features of the torus configuration (TMA, donut)

A subsequent reduction in the cross-section of the wire and the overall size of the coil will lead to the creation of an even more effective version of the vortex capacitance. With an outer diameter of 51 mm and an inner diameter of 25 mm, a wire thickness of about 0.1 mm is created.

Such a device is difficult to make by hand. Therefore, it is recommended to use a simplified version of manufacturing the device in the form of a torus.

Making a torus

To make a torus, you will need about 15 meters of twisted pair cable (UTP 5E). The wire includes four or eight cores, which are twisted in pairs. You should remove the outer insulation of the cable and separate one pair from the rest.

To create such a container, you can use almost all types of wires. The only condition is that the distance between the wires along the entire length must be the same. Therefore, twisted pair is ideal.

Next, a piece of electric corrugation is used. It will become the basis for creating equipment for bobbin winding. The diameter of the corrugation should be 25 mm. It should be bent into a torus of the required size. A slot is made along the outside. It is secured with a couple of turns of insulating tape.

This winding will ensure the correct formation of vortices. In this case, a whole spectrum of frequencies is formed, where the inner part of the winding is responsible for high performance, and the outer part for low ones.

Before you start winding, the internal lead of the wire should be threaded into a pre-prepared hole in the corrugation, and after winding, fix the outer leads. To secure the winding, it is necessary to remove the corrugation in parts. Twisted pair leads unwind, and unused ones are bitten off

Determining the device power frequency

Next, you should determine the frequency of the torus power supply. The generator terminal must be connected from different sides to the wires of the device. To determine the output voltage, the oscilloscope probes are connected directly to the generator terminals.

Then the first indicator of the frequency of the maximum voltage drop relative to the input is determined. In other words, the frequency of maximum conductivity of the capacitance should be indicated. Further nutrition will take place precisely at this indicator.

Coil power supply

The coils are powered by a sine wave (signal from the generator). Power supply via pulses is unacceptable, since it does not have inertia in this mode. The high efficiency frequency range for toroids is the same as for flat coils. It is 270-380 kHz.

During operation of the device, the supply voltage coming from the generator can drop up to ten times or more. In this case, the total power supply activity indicator can be no higher than 0.1 W. The maximum conducting current power should be limited to 200 mA, and the voltage to 22-24 V.

If these parameters are overestimated, this can lead to electrostatic breakdowns, which will be expressed in discharges from the center of the coil.

What generators should I use?

A frequently used generator for the Mishin coil is TGS-3. It has automated resonance tuning.

The ATTEN ATF20B+ model is considered a more professional analogue. Its advantages include the presence of a display, USB interface, frequency counter, and signal shape. Such a generator for the Mishin coil emits a signal that is not subject to distortion.

Mishina coil treatment

So, by preparing a device of the simplest configuration in the form of an inductive coil, it is possible to influence any problem areas of living organisms for therapeutic purposes. In most cases, knowledge of painful points in the body is not at all necessary, since electrostatics automatically affects painful volumetric structures and contributes to their separation.

What is vortex medicine based on? Mishin coils provide natural application of environmental energy to influence the problems arising in the carbon form of life. This method is equivalent to the effects of antibiotics, and also serves as a replacement for operations to remove cancerous tumors. The vortex flows created by the coil will easily restore the affected nerve cells.

What did the testing of the device show?

What potential does the Mishin coil have? Treatment with it gives good results. Tests that were carried out over a number of months revealed a high level of effectiveness of using electrostatic capacitance to restore lost body functions. The duration of one session, depending on the disease, ranged from 5 minutes to an hour.

Features of the treatment of certain diseases

The Mishin coil causes the release of large amounts of toxins, which must be eliminated by the kidneys through urine. Dealing with so many harmful substances when using a coil is not an easy task. Therefore, treatment begins with the lumbar region.

For a normal body cleansing regime, sessions lasting 30-40 minutes will be sufficient. They should be carried out within the first five days. The coil is applied to the lumbar and chest area. The lower back is the most important area of ​​influence during treatment, as the kidneys are cleansed. These organs, as statistics show, are severely clogged in half of the people.

The first week of treatment contributes to significant cleansing of the body. The immune system works in enhanced mode, tissue regeneration begins.

The duration of sessions held in the second week can be increased to 60-90 minutes. This is the average. Much depends on the specific case and disease.

For example, kidney treatment should be carried out in sessions lasting half an hour. If after the procedure the patient complains of feeling unwell, weakness, chills, fever, pain, then the Mishin coil has begun its effect. If a person is able to bear the discomfort, then a similar session is carried out the next day. If you feel very bad, it is recommended to postpone treatment for two days.

Each person is able to determine what intensity of exposure he needs to be cured. The patient chooses the duration of the session individually.

At first, the coil may have little effect on obese people. Electrostatics have a certain charge that is consumed as waste products break down in the body. It promotes the destruction of looped formations. During the next session, without encountering any obstacles on its way, electrostatics penetrates even deeper and copes with the disease. Cell formation, as a rule, is located in the fat layer. This is why overweight people require a longer period of treatment. Typically, such patients do not feel any results from the sessions within the first five days.

Choosing the right mode

After the Mishin coil begins to act, you need to decide whether this mode is right for you, whether it is worth adding exposure time or whether it should be reduced. If you are on vacation, you can resort to daily long-term procedures. This way you can cleanse your body in the shortest possible time. It can also be used in shorter sessions. This intensity is applicable to people who do not have any severe acute illnesses that require urgent treatment.

A local disease, for example, pain in the knees or migraine, can be treated with another device - a torus. This bagel has a targeted effect and is perfect for these purposes. The impact diameter of the device is approximately 10 cm.

Features of the coil

There are nuances in the operation of the coil that are difficult to explain.

For example, the coil continues to work even when turned off. Only the indicator of its functionality in this case is 20%. In addition, the impact extends not only to the person to whose body the coil is attached, but also to people who are at a distance of 3-7 meters from it.

Many people are interested in how long a device such as a Mishin coil can be used. Treatment should be stopped after the body has rid itself of all toxins, as the device no longer has any effect on the body. You can apply the coil to your body throughout the day, but it will not have any effect. This is what will indicate that you have improved your health.

For more than a hundred years, humanity has been using electrical energy on a large scale. A huge number of all kinds of devices have been produced that are constantly located directly next to us, but not one of the textbooks gives an accurate physical description of the energy source itself - electric current. At the same time, we hardly think about the simplest biological safety in shi x devices, and, as time has shown, absolutely in vain. Over the past decades, there has been a sharp increase in all kinds of pathologies of human internal organs, the intensive development of cancer and many completely new diseases, against which traditional medicine is powerless. The reason for all this is not so much environmental pollution as a lack of understanding of the physical processes in all our devices based on electromagnetism.

Physics of processes

If we touch on the physics of processes, then in nature everything is carried out on the basis of the law of conservation of momentum, or, to put it more simply, it is impossible to perform an action without having a support point, and at the moment of its completion, both the object and the support will receive the same mechanical impact . If we consider this from the point of view of vortex processes, it turns out that when creating any electromagnetic interactions in a standard way, we rely on the transverse electrostatic (electric) plane. Our biological life is now placed in an environment where there is constant pulsation from all our devices, which continuously influence molecular structures. The main effect of electrostatics is direct mechanical work to increase the frequency of rotation (twisting) of the vortex shells of molecules and their groups. As a result, they become oversaturated with energy, leading to the formation of larger clusters. This phenomenon can be roughly compared with the formation of “balls” of metal after welding, or in relation to the weld itself. It turns out that the sharply increased strength of new formations is associated with the cycling of the structure along the electromagnetic axis of the molecular structure. Further impact on such structures by mechanical (shock) methods is ineffective. The same thing happens in the human body. Many looped molecular structures are not amenable to drug treatment due to their increased strength. However, such formations in the body lead to the formation of tumors due to their excess energy (hyperactivity), or to blocking any other functions of the body.

The solution to this problem lies precisely in the field of electrostatics. An increase in the energy of processes is associated with a decrease in the density of the medium between molecular clusters, which leads to their stability. It is necessary to ensure an influx of medium into the cluster to create a demagnetization effect. Next, the medium itself will fill the intermolecular space, which will sharply weaken such vortex connections. The easiest way to do this is to create a zone of reduced density of the medium using electrostatic implosive resonance. At the physical level, this is the phenomenon of absorption (fall) of the medium into a zone of low density. This process can be created using a simple interturn capacitance. There is only a basic difference between the capacitors we are used to and what we need to do. In the first case, we are trying to increase the capacitance, minimizing the inductance of the capacitor, and in the second, we create a minimum capacitance, but with maximum inductance, while the inductance of the plates themselves should tend to zero during operation. Having created such a capacitance, we get the exact opposite of a standard capacitor; it does not accumulate a “charge”, but spins two electrostatic vortices (standing wave), above and below relative to the equator zone. Operation in this mode is possible only in a certain frequency range, which is determined only by the geometry of the capacitance itself. A strong deviation from the operating frequency sharply reduces the conductivity of the capacitor and, accordingly, the formation of electrostatics. In the nominal operating mode, two zones of decreasing medium density relative to the equator are formed, after which electrostatic suction occurs into the center of the device. At its core, this process is almost no different from the “gravity” we are used to, having only a small radius of action of only 2-3 meters. The power transmitted through such a capacitance depends on the applied voltage. For health purposes, the power of standard frequency generators with an output voltage of 12-24 volts and a current not exceeding 100-200 mA is sufficient.

Manufacturing of flat coil-disc (DMA)

Let's consider several options for the design of such containers and their manufacturing sequence.

The photo shows a flat coil â capacity,Ãàmade of 2 MGTF wires 0.12 longÃà~20 meters.ÃÃÂ

A base is pre-made, onto which double-sided tape is glued. In the center we install a round protrusion with a diameter of approximately 25 mm, around which we begin to lay two wires at once parallel to the plane of the base.

After completing the manufacture of such a flat coil, we obtain a container of two spiral plates nested inside each other. It is possible to use any copper wire, the diameter of which together with the insulation does not exceed 1.5 mm, while the diameter of the coil should not exceed 23-25 ​​cm.

Fixing the wire on top can be done by simply gluing tape or any other convenient method.

Oscilloscope setup

After manufacturing the coil, it is necessary to determine the frequency of operation of this container. We make two leads from the coil, taking the end of one wire from the inside of the coil and the second from the other wire outside. In this case, the circuit remains open, and the two unused outputs of the plates are simply cut off.

When using a standard generator with a power of up to two watts, it is possible to determine the operating frequency by simply connecting the oscilloscope probe in parallel with the generator terminals. Smoothly increasing the frequency of the generator, we look for the first frequency at which the output voltage of the generator is the lowest; this will be the operating frequency of this capacitance.

The second option is to measure the voltage across a 1 Ohm resistor connected in series in the power circuit.

In this case, we are looking for the first largest amplitude value, and this measurement method also allows us to evaluate the quality of the supplied sine wave in capacitive load mode.

Setting by LED indicator

In the absence of an oscilloscope, you can determine the operating frequency of the capacitance using an indicator coil, which is an inductance coil whose load includes 2 counter LEDs.

With this method, the search for frequency is based on the maximum luminosity of the LEDs; in this case, the generator voltage must be reduced, thereby reducing the frequency range at which the luminescence is observed.

Coil frequency

If you fasten the wire well and do not subject the coil to severe mechanical deformation, then after determining the optimal frequency of supplying the container, its frequency will not change during operation. For the above capacitor design, the approximate frequency is 310 kHz, while the effective power supply range lies within Ãñ10 kHz relative to the operating frequency. The capacitance manufactured in this way has a wide electrostatic spectrum and a low gradient of density change towards the center of the coil during operation. This allows you to work effectively at the level of the central nervous system, eliminate circulatory problems and many other small vortex problems of living organisms.

Reel 12cm in varnish

A container with a reduced distance between the plates will be more powerful in its impact on pathogenic formations. For example, it can be done with a wire 0.5 mm in diameter in varnish insulation, the length of each wire will be 10-12 meters. The inner diameter will also be approximately 25mm, and the outer diameter 120-130mm. Such a container works much more effectively with smaller (at the physical level) problems, such as viruses and fungal diseases, and can quickly remove scar tissue and accelerate healing.ÃÃÂ

Detailed video instructions for making a 12cm varnished coil:

Thor (TMA, donut)

Further reductions in wire diameter and overall coil size form an even more aggressive version of the vortex capacitance. At the same time, the overall dimensions of 51mm outer diameter and 25mm inner diameter set the wire thickness to about 0.1mm for making a coil, which creates significant difficulties when creating it manually. A simplified version of production in the form of a torus is possible.

Making a torus

For production you will need a twisted pair cable (UTPÃÃÂ 5E) approximately 15 meters long. The wire consists of four or eight strands twisted in pairs. We need to strip the outer insulation of the cable and separate one pair from the rest. To create such containers, it is possible to use almost any type of wire; the only condition is to form the same distance between the wires along the entire length, so the easiest way to use the available materials is twisted pair.

Next, you can use a piece of electric corrugation to create equipment for winding the coil. We bend the corrugation (diameter 25mm) into a torus of the size we need to get the torus hole approximately 50% of the total diameter of the container, make a slot along the outside and fix it inside with a couple of turns of electrical tape. This winding allows you to maintain the correct vortex formation parameters. At the same time, we form a whole spectrum of frequencies, where the internal part of the winding is responsible for the high frequencies, and the external part is responsible for the low frequencies of the spectrum. Before starting winding, we thread the internal lead of the wire into a pre-prepared hole in the corrugation, and then
winding, we fix the external terminals. To secure the winding, you can remove the corrugation in parts, securing the coil with electrical tape.

We unwind the leads of the twisted pair, and simply bite off the unused leads.ÃÃÂ Next, we determine the power supply frequency of our torus, as well as the previous flat coils. The generator terminals are connected from different sides to different wires of the vortex capacitance. The oscilloscope probes are connected directly to the generator terminals to determine the output voltage. We determine the first frequency of the maximum voltage drop relative to the input. In other words, we determine the frequency of maximum conductivity of the vortex capacitance. Further power will be provided at this frequency.

Coil power supplyÃÃÂ

The coils are powered by a sine wave (sinusoidal signal from the generator). Pulse power supply for the tank is unacceptable, because it has no inertia in this mode. The effective frequency range for tori is the same as for flat coils â 270-380 kHz. While the tank is operating, the supply voltage supplied by the generator may sag up to ten or more times, while the total active power supply may not exceed 0.1 watt. The maximum input power should be limited in current to 200 mA, and voltage to 20-24 volts. Exceeding these parameters can lead to electrostatic breakdowns in the form of discharges from the center of the coil.

Treatment

So, armed with a simple device in the form of an inductive capacitance, we can easily and precisely influence all problem areas of living organisms. In most cases, we do not need complex equipment to determine where and what problems arise in the body; electrostatics is automatically aimed at looped volumetric structures and disconnects them. It is a pure natural method of using the energy of the environment to influence the problems of the carbon-based life form. This method can completely replace antibiotics, multiple operations to stop the development of tumors, and restore the central nervous system quite easily and quickly.

Tests carried out over several months have shown the highest effectiveness of electrostatic implosion in restoring vital body functions. The time the container remains (1 session) on the problem area can vary from 5 minutes to an hour, depending on the geometry of the device and the disease.

Where to start treatment

For a normal regime of cleansing the body, it is enough to start with a large flat container for 30-40 minutes a day, for the first five days, applying it to the lower back and chest. The lower back in this case is number one on the list, because The coil at this moment cleans the kidneys, which, as practice has shown, every second person is quite clogged. During the first week, the body is significantly cleansed, and the functions of immunity and regeneration are launched in an enhanced mode.

During the second week, you can increase the duration of exposure with a container of a smaller diameter to 60-90 minutes. Here, a lot depends on the specific case and problems in the body, these are only average figures, each person is able to feel for himself how quickly he can eliminate the disease.

Possible side effects

Removing many old problems of the body is often associated with a short-term exacerbation; you should not be afraid of this, because if the destroyed sore was deep in the body, then it will make its way out.

It is possible that the temperature may rise from several hours to two or three days, and nagging pain in the muscles may occur. After the static interacts with the body, many toxins that were “lying” in the body enter the bloodstream, which leads to a slight increase in blood pressure and drowsiness. If possible, you need to let the body eliminate this without loading it with anything else. In this case, sleep helps the body cope very well with this.

Statics does not affect healthy cells

After removing the main problems from the body, it practically stops responding to the electrostatics of the containers, because there are no more looped geometric structures left. Further use makes sense when symptoms of diseases occur; 15-20 minutes is usually enough to stop almost any developing problem. It makes no sense to list the range of effects on medical problems here; this is a huge variety of diseases.

This method can only harm normal cells of the body if the power supply ripples are too powerful, so it is recommended to use the sine and parameters given above in the description of the containers.

Effect on plants

It also makes sense to use such devices in livestock and crop production. Potentially, electrostatic treatment will be of great help in the fight against animal and plant diseases. Several experiments have shown that when indoor plants are exposed to static, increased growth is observed, as well as accelerated seed germination.

Ways for further development of technologyÃÃÂ

At the moment, the use of implosion technologies is taking its first steps, but copying the principles of life of the nature around us easily overshadows everything that we use now. The potential for the development of electrostatic devices, in fact, is limited only by our understanding of the surrounding reality, and with further development it carries endless potential. Many people now don’t even understand what we’re talking about, but this is only because from childhood we were taught a completely different way of thinking, excluding from understanding even the purpose of our stay on Earth. ÃÓI don’t believe in thisâæÃÔ â says the vast majority, without even thinking about the fact that believing and thinking are completely different things. The body of each of you lives only as long as consciousness develops. You shouldn’t “believe” or “don’t believe”, just look at the surrounding nature and try to understand why it is the way it is, what processes allow her to live, and which ones destroy her.

Sine generator

The photo shows a recommended sine generator, specially designed to work with coils. Unlike many industrial generators, the output has a pure sine wave and is not distorted when connecting coils like the utg9002c and many others. ÃÃÂ In addition, it hasÃÃÂ low cost.

For more than a hundred years, humanity has been using electrical energy on a large scale. A huge number of all kinds of devices have been produced that are constantly located right next to us, but not one of the textbooks gives an accurate physical description of the energy source itself - electric current. At the same time, we hardly think about the simplest biological safety of our devices, and, as time has shown, it is absolutely in vain. Over the past decades, there has been a sharp increase in all kinds of pathologies of human internal organs, the intensive development of cancer and many completely new diseases, against which traditional medicine is powerless. The reason for all this is not so much environmental pollution as a lack of understanding of the physical processes in all our devices based on electromagnetism.

Electromagnetic causes of pathologies

If we touch on the physics of processes, then in nature everything is carried out on the basis of the law of conservation of momentum, or, to put it simply, it is impossible to perform an action without having a fulcrum, and at the moment of its commission both the object and the support will receive the same mechanical impact. If we consider this from the point of view of vortex processes, it turns out that when creating any electromagnetic interactions in a standard way, we rely on the transverse electrostatic (electric) plane. Our biological life is now placed in an environment where there is constant pulsation from all our devices, which continuously influence molecular structures. The main effect of electrostatics is direct mechanical work to increase the frequency of rotation (twisting) of the vortex shells of molecules and their groups. As a result, they become oversaturated with energy, leading to the formation of larger clusters. This phenomenon can be roughly compared with the formation of “balls” of metal after welding, or in relation to the weld itself. It turns out that the sharply increased strength of new formations is associated with the cycling of the structure along the electromagnetic axis of the molecular structure. Further impact on such structures by mechanical (shock) methods is ineffective. The same thing happens in the human body. Many looped molecular structures are not amenable to drug treatment due to their increased “strength”. However, such formations in the body lead to the formation of tumors due to their excess energy (hyperactivity), or to blocking any other functions of the body.

Implosion

The solution to this problem lies precisely in the field of electrostatics. An increase in the energy of processes is associated with a decrease in the density of the medium between molecular clusters, which leads to their stability. It is necessary to ensure an influx of medium into the cluster to create a demagnetization effect. Next, the medium itself will fill the intermolecular space, which will sharply weaken such vortex connections. The easiest way to do this is to create a zone of reduced density of the medium using electrostatic implosion resonance. At the physical level, this is the phenomenon of absorption (fall) of the medium into a zone of low density. This process can be created using a simple interturn capacitance. There is only a basic difference between the capacitors we are used to and what we need to do. In the first case, we are trying to increase the capacitance, minimizing the inductance of the capacitor, and in the second, we create a minimum capacitance, but with maximum inductance, while the inductance of the plates themselves should tend to zero during operation. Having created such a capacitance, we get the exact opposite of a standard capacitor; it does not accumulate a “charge”, but spins two electrostatic vortices (standing wave), above and below relative to the equator zone. Operation in this mode is possible only in a certain frequency range, which is determined only by the geometry of the capacitance itself. A strong deviation from the operating frequency sharply reduces the conductivity of the capacitor and, accordingly, the formation of electrostatics. In the nominal operating mode, two zones of decreasing medium density relative to the equator are formed, after which electrostatic suction occurs into the center of the device. At its core, this process is almost no different from the “gravity” we are used to, having only a small radius of action of only 2-3 meters. The power transmitted through such a capacitance depends on the applied voltage. For health purposes, the power of standard frequency generators with an output voltage of 12-24 volts and a current not exceeding 100-200 mA is sufficient.

How to make a flat coil (DMA)

Let's consider several options for the design of such containers and their manufacturing sequence.

In the photo, the flat coil is a container made of 2 MGTF 0.12 wires ~20 meters long.

A base is pre-made and double-sided tape is glued onto it. In the center we install a round protrusion with a diameter of approximately 25 mm, around which we begin to lay two wires at once parallel to the plane of the base.

After completing the manufacture of such a flat coil, we obtain a container of two spiral plates nested inside each other. It is possible to use any copper wire, the diameter of which together with the insulation does not exceed 1.5 mm, while the diameter of the coil should not exceed 23-25 ​​cm.

Fixing the wire on top can be done by simply gluing tape or any other convenient method.

Oscilloscope setup

After manufacturing the coil, it is necessary to determine the frequency of operation of this container. We make two leads from the coil, taking the end of one wire from the inside of the coil and the second from the other wire outside. In this case, the circuit remains open, and the two unused outputs of the plates are simply cut off.

When using a standard generator with a power of up to two watts, it is possible to determine the operating frequency by simply connecting the oscilloscope probe in parallel with the generator terminals. Smoothly increasing the frequency of the generator, we look for the first frequency at which the output voltage of the generator is the lowest; this will be the operating frequency of this capacitance.

The second option is to measure the voltage across a 1 Ohm resistor connected in series in the power circuit.

In this case, we are looking for the first largest amplitude value, and this measurement method also allows us to evaluate the quality of the supplied sine wave in capacitive load mode.

Setting by LED indicator

If you do not have an oscilloscope, you can determine the operating frequency of the capacitance using an indicator coil, which is an inductor coil whose load includes 2 counter LEDs.

With this method, the search for frequency is based on the maximum luminosity of the LEDs; in this case, the generator voltage must be reduced, thereby reducing the frequency range at which the luminescence is observed.

Effective coil frequency

If you fasten the wire well and do not subject the coil to severe mechanical deformation, then after determining the optimal frequency of supplying the container, its frequency will not change during operation. For the above capacitance design, the approximate frequency is 310 kHz, while effective frequency range of the supply signal lies within ±10 kHz relative to the operating frequency. The capacitance manufactured in this way has a wide electrostatic spectrum and a low gradient of density change towards the center of the coil during operation. This allows you to work effectively at the level of the central nervous system, eliminate circulatory problems and many other small vortex problems of living organisms.

Features of 12cm flat reel

A container with a reduced distance between the plates will be more powerful in its impact on pathogenic formations. For example, it can be done with a wire 0.5 mm in diameter in varnish insulation, the length of each wire will be 10-12 meters. The inner diameter will also be approximately 25mm, and the outer diameter 120-130mm. Such a container works much more effectively with smaller (at the physical level) problems, such as viruses and fungal diseases, and can quickly remove scar tissue and speed up healing.

Detailed video instructions for making a 12cm varnished coil:

Features of a torus (TMA, donut)

Further reductions in wire diameter and overall coil size form an even more aggressive version of the vortex capacitance. At the same time, the overall dimensions of 60mm outer diameter and 25mm inner diameter set the wire thickness to about 0.1mm for making a coil, which creates significant difficulties when creating it manually. A simplified version of production in the form of a torus is possible.

How to make a torus

For manufacturing you will need a twisted pair cable (UTP 5E) approximately 15 meters long. The wire consists of four or eight strands twisted in pairs. We need to strip the outer insulation of the cable and separate one pair from the rest. To create such containers, it is possible to use almost any type of wire, the only condition is to create the same distance between the wires along the entire length, so the easiest way to use the materials at hand is twisted pair.

Next, you can use a piece of electric corrugation to create equipment for winding the coil. We bend the corrugation (diameter 25mm) into a torus of the size we need to get the torus hole approximately 50% of the total diameter of the container, make a slot along the outside and fix it inside with a couple of turns of electrical tape. This winding allows you to maintain the correct vortex formation parameters. At the same time, we form a whole spectrum of frequencies, where the inner part of the winding is responsible for the high frequencies, and the outer part for the low frequencies of the spectrum. Before starting winding, we thread the internal lead of the wire into a pre-prepared hole in the corrugation, and then
winding, we fix the external terminals. To secure the winding, you can remove the corrugation in parts, securing the coil with electrical tape.

We unwind the leads of the twisted pair, and simply bite off the unused leads. Next, we determine the power frequency of our torus, as well as the previous flat coils. The generator terminals are connected from different sides to different wires of the vortex capacitance. The oscilloscope probes are connected directly to the generator terminals to determine the output voltage. We determine the first frequency of the maximum voltage drop relative to the input. In other words, we determine the frequency of maximum conductivity of the vortex capacitance. Further power will be provided at this frequency.

Coil power supply

The coils are powered by a sine wave (sinusoidal signal from the generator). Switching power supply for the tank is unacceptable, because it has no inertia in this mode. The effective frequency range for tori is the same as for flat coils - 270-380 kHz. While the tank is operating, the supply voltage supplied by the generator may sag up to ten or more times, while the total active power supply may not exceed 0.1 watt. The maximum input power should be limited in current to 200 mA, and voltage to 20-24 volts. Exceeding these parameters can lead to electrostatic breakdowns in the form of discharges from the center of the coil.

Treatment

So, armed with a simple device in the form of an inductive capacitance, we can easily and precisely influence all problem areas of living organisms. In most cases, we do not need complex equipment to determine where and what problems arise in the body; electrostatics is automatically aimed at looped volumetric structures and disconnects them. It is a pure natural method of using the energy of the environment to influence the problems of the carbon-based life form. This method can completely replace antibiotics, multiple operations to stop the development of tumors, and restore the central nervous system quite easily and quickly.

Tests carried out over several months have shown the highest effectiveness of electrostatic implosion in restoring vital body functions. The time the container remains (1 session) on the problem area can vary from 5 minutes to an hour, depending on the geometry of the device and the disease.

Where to start?

For a normal body cleansing regimen, it is enough to start with a large 19cm flat coil for 30-40 minutes a day, for the first five days, applying it to the lower back and chest. The lower back in this case is number one on the list, because The coil at this moment cleans the kidneys, which, as practice has shown, every second person is quite clogged. During the first week, the body is significantly cleansed, and the functions of immunity and regeneration are launched in an enhanced mode.

During the second week, you can increase the duration of exposure with a container of a smaller diameter to 60-90 minutes. Here, a lot depends on the specific case and problems in the body, these are only average figures, each person is able to feel for himself how quickly he can eliminate the disease.

Possible side effects

Removing many old problems of the body is often associated with a short-term exacerbation; you should not be afraid of this, because if the destroyed sore was deep in the body, then it will make its way out.

It is possible that the temperature may rise from several hours to two or three days, and nagging pain in the muscles may occur. After the interaction of static with the body, many toxins that were “lying” in the body enter the blood, which leads to a slight increase in blood pressure and drowsiness. If possible, you need to let the body eliminate this without loading it with anything else. In this case, sleep helps the body cope very well with this.

Statics does not affect healthy cells

After removing the main problems from the body, it practically stops responding to the electrostatics of the containers, because there are no more looped geometric structures left. Further use makes sense when symptoms of diseases occur; 15-20 minutes is usually enough to stop almost any developing problem. It makes no sense to list the range of effects on medical problems here; this is a huge variety of diseases.

This method can only harm normal cells of the body if the power supply ripples are too powerful, so it is recommended to use the sine and parameters given above in the description of the containers.

Effect on plants

It also makes sense to use such devices in livestock and crop production. Potentially, electrostatic treatment will be of great help in the fight against animal and plant diseases. Several experiments have shown that when indoor plants are exposed to static, increased growth is observed, as well as accelerated seed germination.

Ways for further development of technology

At the moment, the use of implosion technologies is taking its first steps, but copying the principles of life of the nature around us easily overshadows everything that we use now. The potential for the development of electrostatic devices, in fact, is limited only by our understanding of the surrounding reality, and with further development it carries endless potential. Many people now don’t even understand what we’re talking about, but this is only because from childhood we were taught a completely different way of thinking, excluding from understanding even the purpose of our stay on Earth. “I don’t believe in this...” says the overwhelming majority, without even thinking about the fact that believing and thinking are completely different things. The body of each of you lives only as long as consciousness develops. You shouldn’t “believe” or “not believe”, just look at the surrounding nature and try to understand why it is the way it is, what processes allow it to live, and what processes destroy it.

Among the budget options, this is the DMAGEN-1 Generator with automatic resonance adjustment.

A more professional generator suitable for working with a Mishin coil - ATTEN ATF20B+

Advantages: display, USB interface, frequency counter, power amplifier, waveforms

The signal when working with Mishin coils is not distorted.

Many answers to coil treatment are given in the video with Alexander.

Conference on Vortex Medicine

Mishin coils. Review from researcher Alexey Kungurov