How to make 2 routers on the same network. Different ways to connect two routers on the same network

Connect your main router to your modem, then connect your computer to the router via an Ethernet cable. Set it up the same way as for regular network. Once the router is connected to the Internet, install it as if it were the only router.

• Most routers can be accessed at 192.168.1.1, 192.168.2.1, or 192.168.0.1.
• Pay attention to the IP address and subnet mask. The IP address is the same as the one you used on the router configuration page. The subnet mask is usually 255.255.255.0.
• If you are creating a LAN-to-WAN network, set up DHCP to distribute addresses between 192.168.1.2 and 192.168.1.50. If you are creating a LAN-to-LAN network, you can leave the DHCP settings at the factory settings.
• Disconnect your computer from the router when you are done with the configuration process.

Connect your computer to the secondary router. Open the configuration page. If you are creating a LAN-to-LAN network, change the IP address so that it matches the address of the first router, except for the last digit, which should be one more (for example, 192.168.1.1 becomes 192.168.1.2). If you are creating a LAN-to-WAN network, change the IP address so that it matches the address of the first router, except for the penultimate digit, which should be one more (for example, 192.168.1.1 becomes 192.168.2.1). Make sure the subnet mask is the same as the first router.

• If you are creating a LAN-to-WAN network, change the IP address of the secondary router to 192.168.1.51.

Configure DHCP server on the secondary router. If you are creating a LAN-to-LAN network, you should first disable DHCP on the secondary router. If you are creating a LAN-to-WAN network, the DHCP server on the secondary router should be with an address between 192.168.2.2 and 19.2.168.2.50

Changing the network channel. If both routers are wireless, you can manually set the channels to prevent their signals from interfering with each other. Set the primary router's channel from 1 to 6, and then set the secondary router's channel to 11.

How to connect a router to a router via wifi? This question is often asked by users who want to expand the coverage area of ​​their router.

Thanks to the use of two combined devices, you can significantly improve the quality of your Internet connection and increase your Wi-Fi coverage area by almost two to three times.

You can expand your router's coverage area by boosting the antenna. You can also not amplify, but buy separately and install more powerful antenna.

This method is less expensive because you don’t need to buy another one new router.

However, if the antenna improvement method does not bring any results, you can try setting up an access point on two routers at the same time.

First you need to determine approximate diagram mutual connection of two devices.

Schematic example of connecting two routers

If you want to connect a router to transmit a signal over longer distances, you should familiarize yourself with basic circuit connecting these two devices.

It can be used to connect a network in an apartment and in any other private sector.

Approximate diagram as follows:

According to this diagram, there are only two ways to interconnect two routers: through a wire and wireless way connections. Let's take a closer look at them.

Connecting two routers using a wire

The easiest way to connect two routers to one access point is the wired method. To work, you will need the most common UTP cable, another name for it is twisted pair.

You can purchase it at any telecommunications store.

The average market price of this type of cable is 20-30 rubles per meter. Appearance The twisted pair internet cable is shown in the figure below:

To connect two routers using twisted pair, follow the instructions:

• Make sure both sides of the cable have adapters. Also make sure that the cable size matches the distance from one router to another;
• Take two routers;
• Connect them using a cable. Connect twisted pair To LAN port the router that is configured to connect to the Internet. Connect the other end of the cable to the WAN connector of the unconfigured router. Another router will transmit the signal over a long distance;
• Now just configure the router connected to the Internet in the standard way, and assign a dynamic IP to the other router.

Advice! The disadvantage of this connection method is that in some cases it is inconvenient to lay the cable on long distances(when you want to create coverage between several floors, for example).

Also, the cable may become susceptible to mechanical breakdowns, which cannot be corrected and then you will have to buy new cable.

Wireless connection between two routers

This type connection does not require any wires. However, the complexity of this method lies in the fact that it is very important to configure the equipment correctly:

• Take a router to which the Internet will be connected;
• The second router will be the access point;
• Set up your first router in a standard way as if you were using only one router;
• Now connect your computer to another router;
• Using the Control Panel, open the Settings window wireless network, in which select the Internet protocol selection window.
  Select the second router and configure the IPv protocol for it. Then click on the properties tab and enter the following text (without quotes) in the next address usage field - “192.168.1.254”;
• Save your settings and open your browser. In the address bar, enter "192.168.1.254". The settings menu for the second router will open;

• Click on the “search” button;
• A window will open with a list of available wireless networks. Select the network of the first router and press the save key;

• Reboot both access points.

This article will help those people who need to build a wireless network in a large room, when the signal from one access point or router does not cover the entire area. For example, in a multi-storey private house or if you want to have Internet not only inside the house, but also, for example, in a gazebo on the street.

I bring to your attention the most stable version of this solution. I connected devices from different eras to the network - a D-Link DIR-300 NRU hardware version B1 from 2010 and an old D-Link DI-624 from 2006. They have completely different hardware and wi-fi different classes and accordingly different speeds.

So we have two routers. It is convenient for us to designate them as main And secondary.
IN main The router is connected to the Internet provider cable and it will work in router mode.
A secondary the router will operate in access point mode: it will not route anything, but will only relay the signal.

Step 1. Set up on both Wi-Fi devices. It is necessary that SSID, security type, encryption type and network key were the same, but the channels were different. It is recommended to use non-adjacent channels - 1, 6, 13.

Step 2. We connect to the secondary router and turn off the DHCP server on it. This is necessary so that in a certain situation there are no problems with Internet access.

Step 3. Connecting LAN port s routers using a patch cord.

As a result, we get this diagram:
The provider's cable is connected to the WAN (or DSL) port of the main router. A cable is connected to the LAN port, connecting the main router to the secondary router through the same LAN port.

Click to enlarge

So I set up main router with the following parameters:

IP address = 192.168.1.1

DHCP server = enabled

SSID= homebase
Wireless Channel = 13
Wireless Security Mode = WPA2
Cipher Type = AES
PSK/EAP = PSK

AND secondary with these:

IP address = 192.168.1.254
Subnet mask = 255.255.255.0
DHCP server = disabled

SSID= homebase
Wireless Channel = 1
Wireless Security Mode = WPA2
Cipher Type = AES
PSK/EAP = PSK

Those. The only difference we have is in the broadcast channels and DHCP turned off on the secondary router. The DHCP server of the main router operates in the constructed network. It is relayed by the secondary router. Those. If work station connects via Wi-Fi to the secondary router, it receives an IP address from the correct pool and the default gateway we need, which corresponds to the main IP address.

When the device is physically moved out of range WiFi signal one router into an area where the signal of another is dominant occurs automatic reconnecting the device to a router with a stronger signal. There is minor internet interruption. You can see it in the console by pings remote server, for example ya.ru. Literally 1-2 packages are lost. Your devices, such as a smartphone, tablet, netbook, will see a single wireless network. Only with the help of special software, such as InSSIDer, can it be determined that the network consists of several access points.

Modern home appliances are getting smarter (and bolder) every year. If yesterday only computers and mobile phones needed an Internet connection, today, perhaps, only irons, and even then not all, can do without the World Wide Web. Of course, this is progressive, but how can such a bunch of different devices be provided with an uninterrupted connection to the network, especially in big apartment? One router is clearly not enough for them.

Don't rush into buying an expensive multiport router. To solve this problem, a pair of simple home routers that will work together in one local area is usually enough.

F1comp has already talked about how to connect two routers to one network, and today, in continuation of the topic, we will talk about wired ways connections.

Wifi is good, but cable is better

• You need to connect your device to the Internet without a Wi-Fi adapter.
• The room area is very large, and the distance between access points is more than 30 m.
• Are you going to connect to World Wide Web set-top box or Smart TV to watch movies high resolution. A wired connection, especially PLC (Internet over Household Power), provides much more best transmission such a signal.
• The indoor environment is too noisy or there is a lot of interference for Wi-Fi transmission.
• Do you want to lower your level? electromagnetic radiation from the access point.

While creating local network with one Internet source, one of the two routers will perform its immediate functions - traffic routing. Let's call it conditionally leading. The second, the slave, will work as a link that collects and forwards traffic from connected devices to the master router.

Methods for connecting routers with a network cable

Method 1: LAN+LAN

The leading router (1) is connected to the provider’s equipment via the Internet or WAN port and is configured to work in its network. You do not need to change anything in its settings, except for activating the DHCP server (if it was previously disabled).

After this, assign a different IP address to the LAN port of the slave router, different from the address of the main gateway, but included in the same subnet. For example, if the IP of the main gateway is 192.168.0.1, you can register 192.168.0.11 instead. Just make sure that this address is not used by other devices connected to the same local network.

If the slave router was previously used as the main router and contains any settings, please restore it to its factory state first, otherwise errors may occur when connecting.

Method 2: LAN+Internet

We leave the settings of the master router unchanged, as in the previous version, and enable only DHCP. And on the slave in the section " Net» – « WAN» – « Connection typeWAN» select « DynamicIP address" After saving the settings, the Internet should appear on it.

If LAN ports will be used on the slave router, also make sure that their IP addresses do not conflict with those of the master.

After this, a separate access point can be launched on each of the routers. If everything is done correctly, both will be connected to the World Wide Web.

Connection using PLC adapters

PLC(Power line communication) – transmission network traffic from device to device via household power supply – the best way connecting to the Internet Smart TVs (it was said above why), as well as other devices that do not support wireless communication. The main advantage of this method is that the reliability and speed of the connection is no worse than that of cable Ethernet networks, and there is no need to lay a cable. Another important advantage is ease of use: insert the wire, plug it into the socket - and you're done, no drivers or settings required.

What this type of communication is and how it works is shown in the figure below. I think it is clear without explanation.

PLC adapters are sold in sets of 2-3 modules. Outwardly they look a little like charging device from mobile phones, but instead of USB sockets they have 1 or several RJ-45 connectors into which the patch cord connector is inserted. The second connector, accordingly, is connected to the device, in our case – the LAN or WAN port of the router.

The electrical cable between two plugged-in adapters becomes the transmission medium.

To use PLC, 3 conditions must be met:

• Good electrical wiring in the house.
• An unbroken line between connection points.
• Availability of an electrical outlet near the device (router).

Setting up routers connected to the same network via PLC is no different from setting up a cable connection.

Also on the site:

How to connect two routers to one network using a cable updated: December 16, 2017 by: Johnny Mnemonic

If you want to increase your productivity home network, then you should seriously think about buying two routers. By connecting two routers over one local network, you will ensure an increased range of the Wi-Fi network, which is great for both home and office premises. There are two methods for connecting routers over a network.

1. Connect wireless Wi-Fi routers to a local network

Step 1

The first step is to determine whether your routers are compatible for bridging. You can look this up both in the router documentation and on the Internet. If you discover that your router does not support bridge modes (“bridge”/”repeater”), you can always download DD-WRT program, it will help you introduce this function if you are installing two routers, connecting them into one network.

Step 2

Install the routers nearby, this will make it much easier to perform further manipulations with the connection. Upon completion of the merger, the equipment can be returned to its place.

Step 3

Choose the main router from the two, the main thing is that it has stronger antennas, which will help you easily install a second router. After connecting the main router to the modem, connect it to one, shared local network of your PC, we carry out the manipulations as with a simple installation of a wireless network. Don't forget about the IP address, DHCP range, don't forget about the mask.

Step 4

Connect the second router to your PC or laptop using Ethernet cable, but for this you do not need to connect the router to the modem. After that, open the router settings window on your computer. Find the Wireless and Internet tabs.

Step 5

If the router can support a bridge connection, then open the Network Mode (Wireless Mode/Connection Type) configuration and select Bridge Mode (Repeater Mode/Repeater Bridge)

Step 6

Check that the mask of the secondary router is identical to the main one. Set the IP range. (For example, the main router is 186.567.1.1 then the secondary router will be 186.567.1.5)

Step 7

Name two connections to Wi-Fi various names so that you know which one is the main one, but the connection type passwords must match.

Step 8

At the final stage, it is worth installing the secondary router in place, but the distance between it and the main one should not exceed more than half the range of the main one.

2. Connecting routers on the same Wi-Fi network

Step 1

As in the previous method, select more strong wifi router, they usually choose a new router with increased configurations. If you have two identical routers, then it doesn’t matter which one you set as the main one.

Step 2

Select an adjacent (secondary) router; it has the function of distributing the Internet when creating a LAN-to-WAN.

Step 3

Place both routers close to your laptop or computer, this will make it more convenient when setting up your wireless network. After the process, you will return the routers to their original places in the room.

Step 4

After completing all the steps before, select the connection. There are two types of connection:

• LAN-to-LAN (local area network) - allows you to increase the size of the network coverage range, and the connection large quantity devices.
• LAN-to-WAN is a global computer network that allows you to set restrictions on certain types of devices. You will be able to specify the sites that can be visited and which are not accessible.

Step 5

Basic Wi-Fi router connects to the modem, and then connect the router via an Ethernet cable to the computer. Then the installation proceeds using the same method as if you were connecting one router.

Step 6

To connect a secondary router, open the configuration window:

• If you are creating a local network (LAN-to-LAN), then you should enter the IP address so that it matches the address of the main router, and the last digit is one more.
• When creating a global computer network(LAN-to-WAN) the process is the same, only the penultimate digit needs to be changed, one more unit.

Step 7

Designate the DHCP server on the secondary router. To connect a local network, you should disable it completely, but if you install global network, then the address should range from 2 to 50 on the last digits.