Detailed instructions for setting up digital television. Settings in TV mode – Operating instructions BBK LT2003S

3. Confirmation will be required, click “OK”.

4. After which the tuner will reset the settings to factory settings.

5. Press “EXIT” and the main menu will appear.

6. Enter the “System Setting” section in the main menu to change the menu language.

7. Select the “Language Setting” section and click “OK”.

8. The language setting menu will open.

9. Change “Menu Language”, “Subtitle Language” and “Audio Language” from “English” to “Russian” using the left and right buttons on the remote control.

11. Press the “Menu” button on the remote control, the main menu will open. Then enter the “Install” menu item.

12. Select “Search for channels” and press “OK”.

13. Select the “Search Mode” line and use the left or right buttons to set the value to “Manual” instead of “Network”.

14. Enter following parameters:

Frequency 322000 Khz (dialed using the remote control channel buttons).
Flow rate 6750 KS/s (selected using the remote control channel buttons).
QAM 64 type (selectable by pressing the right or left button).
Turn on network search(selected by pressing the right or left button).

At correct set settings, two indicators will appear in the lower right corner: “Signal level” and “Quality”.

15. After the indicators appear, use the up or down buttons to move down to the bottom line “Start search” and press the “OK” button.

The receiver will automatically search for channels within 1-2 minutes.

16. A message will appear on the screen indicating the number of television and radio programs found. In order to save the programs, you must click the “OK” button.

After saving (channels), in order to exit, you must press the “EXIT” button on the remote control.

17. In the main menu, enter “Org. Channels".

18. By moving channels, arrange the channels in a sequence convenient for you.

1. Enter "Menu" and select "Factory Settings", click "OK".

2. Enter the password (the default should be 0000).

Then click "OK".

4. Select your desired language.

5. The “Main Menu” will appear, select “Install” and click “OK”.

6. Select Manual Scan and click OK.

7. Enter the frequency: 322000 MHz (using the channel buttons on the remote control).
Flow rate: 6750 (selected using channel buttons on the remote control)
Modulation: 64 QAM (selectable left and right click on the remote)
Set “Network search” to “AVAILABLE” (selected with the left and right buttons on the remote control).

Once the parameters are entered correctly, a signal will appear.

Click “OK” and the tuner will find all channels and radio stations.

To save the channels, click “OK”.

8. Using channel editing, we arrange them in a sequence convenient for you.

1. Press on the remote remote control MENU button. The main menu will open. Use the left and right buttons to select “Channel Tuning”. Select the “Delete all channels” section.

2. Confirmation will be required. Click "OK".

3. The tuner will delete all tuned channels.

4. Select “Installation” in the main menu (using the left and right buttons).

5. Go down to the section “ Manual search» (using the up and down buttons).

6. Click “OK”.

7. Enter the frequency (using the channel buttons on the remote control)

Symbol rate (set by channel buttons on the remote control)
Cable: (selected with the left and right buttons on the remote control)
A signal should appear below.
Click "OK".
The tuner will find channels with the specified parameters.
To save the channels, click “OK”.

To search for other channels, select the next transponder using the right button on the remote control. And enter other parameters for next package TV programs

8. After setting up all TV programs, go to the “Channel settings” in the main menu to move to a sequence convenient for you.

Highlight a channel using the OK button and move it to a position that suits you using the up and down buttons.

1. Press the "MENU" button on the receiver's remote control. The main receiver settings menu will appear on the TV screen.

1.1 By moving the keys up or down on the receiver remote control, you must select the menu line “SEARCH CHANNELS” and press the “OK” button.

2. Press the up or down buttons until we are in front of the “SEARCH PARAMETERS” item in the right column of the menu and press the “OK” button.

3.In the “SEARCH PARAMETERS” menu, enter the parameters one by one:

3.1 Frequency 322000 Khz (selected using the remote control channel buttons).

3.2 Flow rate 6750 KS/s (selected using the remote control channel buttons).

3.3 QAM 64 type (selected by pressing the right or left button).

3.4 After entering the parameters, press the “OK” button and go to the previous menu.

4.Press the up or down buttons until in the right column of the menu we are opposite the line “AUTO SEARCH” and press the “OK” button

4.1 Confirm the action by additionally clicking the “OK” button.

5. Wait for the channel search to finish

1. Press the "MENU" button on the receiver's remote control. The main receiver settings menu will appear on the TV screen.

By moving the keys up or down on the receiver remote control, you must select the “INSTALLATION” menu line and press the “OK” button.

2. The INSTALLATION menu will open. By moving the keys up or down, you must select the “Factory settings” menu line and press the “OK” button.

3. After which the tuner will reset the settings to factory settings.

4. Enter the main menu.

5. Select Install and click OK.

6. Select "Search for channels" and press "OK".

7. The “SEARCH CHANNELS” menu will open.

7.1 Select the line “SEARCH MODE” using the up and down buttons.

7.2 Press the buttons to the right or left until the inscription Manual appears in the right column of the menu opposite the line “SEARCH MODE”.
At the same time, the following lines should become active (it will be possible to change parameters): 2-Frequency, 3-flow rate, 4-QAM type, 5-Network search.

7.3 Enter the parameters one by one:

7.4 Frequency 322000 Khz (selected using the remote control channel buttons).

7.5 Flow rate 6750 KS/s (selected using the remote control channel buttons).

7.6 QAM 64 type (selected by pressing the right or left button).

7.7 Turn on network search (selected by pressing the right or left button).

7.8 If the settings are correct, two indicators will appear in the lower right corner: “Signal level” and “Quality”.

7.9 After the indicators appear, use the up or down buttons to move down to the bottom line “Start search” and press the “OK” button.

8. The receiver will automatically search for channels within 1-2 minutes.

9. A message will appear on the screen indicating the number of television and radio programs found. In order to save the programs, you must click OK.

After saving (channels), in order to exit, you must press the “EXIT” button on the remote control.

10. In the main menu, enter “org. Channels".

11. By moving channels, arrange the channels in a sequence convenient for you.

1. Press the "MENU" button on the receiver's remote control.

2. The main receiver settings menu will appear on the TV screen. Select the item “Search for channels”

3. In the window that appears, select “Quick search”.

4. Enter the following parameters:
◦ Start frequency 346.0 MHz
◦ Transfer rate 6750 kS/s
◦ Search QAM 128-QAM
◦ Network Search Yes
Then select “Search”, the process of searching for channels will begin.

5. When finished, click “OK” in the window that appears and exit the menu with the “EXIT” key

4.In the main menu you need to go to the “Timer” item to set the time

5. Setting up CATV. Go to CHANNEL.

6.Broadcast type, select CABLE TV.

7.Select the search option “DVBC manual search”, and set the following parameters:

Modulation: 64 (QAM) (QAM type)

Your TV is set up.

1. Photo of the TV remote control on which the settings will be made.

2.To enter the TV menu, you must press MENU key on the remote control. Depending on the model, the menu interface may differ, but general meaning and the procedure remains relevant. To do this, go to the SETTINGS item (confirm the selection with the “OK” key on the remote control)

3. Go to the CHANNEL section. Specify the antenna type DVB-C. Go to the Automatic tuning section

4. Scan type Manual DTV setup. Set the following parameters:

Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

Click SEARCH

6.Your TV is configured. By pressing the “EPG” key, a menu will open, electronic program transmission

1. Photo of the TV remote control on which the settings will be made.

2.To enter the TV menu, you need to press the MENU key on the remote control. Depending on the model, the menu interface may differ, but the general meaning and procedure remains relevant. To do this, go to the SETTINGS item (confirm the selection with the “OK” key on remote control)

3.Before you start setting up channels, you need to change the language version of the TV menu (if necessary). To change the language, you need to go to the “Settings” item. (to do this, you need to select this item and confirm the action with the “OK” key on the remote control).

4.To set up TV channels, you need to enter the CHANNELS section.Then select manual setting TV.

5.You need to select DVС TYPE and set the following network parameters:

Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

Your TV is set up.

1. Photo of the TV remote control on which the settings will be made.

3.Before you start setting up channels, you need to change the language version of the TV menu (if necessary). To change the language, you need to go to the “SETUP” item. (to do this, you need to select this item and confirm the action with the “OK” key on the remote control).

4.To set the time, you need to go to the TIME SETTING item.

5.To configure channels, you need to go to the CHANNEL section and select Manual search

6.Select:

Country Russia.
DTV+ATV mode

7.Specify search parameters in accordance with:

Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

1. Photo of the TV remote control on which the settings will be made.

2.Enter the settings menu by pressing the button on the remote control

3. By pressing the “up” and “down” keys, go to the “Channels” section. The connection to TV should be indicated as Cable. If you have an Antenna, try pressing the “Source” key on the remote control and select DTV or DVB-C. If when choosing of this paragraph there is no cable in the options, or the TV does not prompt you to select a signal source at all, perhaps your TV does not have a tuner DVB standard-C

4. Select the “Manual tuning of digital channels” section using the “up” and “down” keys, and confirm the selection with the “OK” key. Next, select the “Digital” option.
5.Next you need to specify the search parameters Search type:

Network search

Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

Click "Start"

7.The TV will ask you to confirm the search, select “OK”. Auto search has started.

1. Photo of the TV remote control on which the settings will be made.

3.Before you start setting up channels, you need to change the language version of the TV menu (if necessary). To change the language, you need to go to the “LANGUAGE” item. (to do this, you need to select this item and confirm the action with the “OK” key on the remote control).

4. Menu language must be specified as “Russian”. Preferred audio language must be specified as “Russian”. Preferred audio language 2 must be specified as “English or Russian”. Then press the “MENU” key to go back.

5.In the main menu you need to go to the “Timer” item to set the time

6.Go to the clock item.

7.In the menu that opens, specify the time and date.Then press the “MENU” key to go back.

8.You need to go to the Settings menu

9.In the setup menu:

The country should be “Russia”;

Tuner mode “Cable TV”;

Go to Channels (by pressing the “OK” key on the remote control)

10.In the Channels menu (go to Manual cable TV setup by pressing the “OK” key on the remote control)

11.In the search menu you need to specify the Country “Russia”

13.Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

Go to the Search item and press the “OK” key on the remote control.

You need to wait until the TV setup is completed.

14.Pressing the “Guide” key will open the menu of the electronic program guide.

1. Photo of the TV remote control on which the settings will be made.

2. Select a language. Using the remote control (hereinafter referred to as the remote control), use the ˂/˃/ ˄ / ˅ arrow buttons to select the “Russian” language. Press the center button to go to the next page.

3. Select a country. Using the remote control using the ˂/˃/ ˄ / ˅ arrow buttons, select the country “Russia”. Press the center button or the right arrow ˃ to go to the next page.

4. Select a location. Using the remote control, use the ˂/˃/ ˄ / ˅ arrow buttons to select the “Home” location. Press the center button or the right ˃ arrow to go to the next page.

5. Start setting up. The screen will display the message “Start Auto Setup?” Press SKIP, then select manual setup options

6. Select the connection type. Using the remote control using the ˄ / ˅ arrow buttons, select the TV connection type “Cable”. Press the center button or the right arrow˃ to go to the next page.

7. Setting up CATV.

Using the remote control, use the ˂/˃/ ˄ / ˅ arrow buttons to select the following values:

Scan Type → Full Scan

Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)

Using the remote control, go to the “Start” button, then press the center button or the right arrow ˃ to go to the next page.

9.Watching KTV.

Digital TV is set up!

To view the channel list, press the “home” button and use the ˂/˃/ ˄ / ˅ arrow buttons to select the “Digital TV” tab.

Next to the TV channel number you can see its name and the program running at that moment.

If your TV model provides for the reception of digital channels, but there is no “DTV MENU” item, then first select another country - France, Switzerland, Sweden or Finland.

1. Press the button - "DTV"
2. click - "DTV MENU"
3. select - "Installation"
4. select - “Manual tuning” Frequency: 322,000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type)
5. click - "OK"
Setup takes approximately 5-10 minutes.

Since not all SONY models are equipped with a digital tuner for cable TV (DVB-C), you need to check the model of your SONY TV.
Models equipped with a DVB-C tuner are marked KDL-**EX*** or KDL-**NX*** - for example KDL-32EX402R2 the first 3 letters in the model name (KDL) indicate that the TV is “digital” . In models KLV-**BX***, etc. DVB tuners No.

1. Press the "MENU" button (for some models it is called "HOME" on the remote control (hereinafter referred to as the remote control). This button is usually blue.
2. Select the “Settings” item.
3. Find the “Digital Configuration” menu in the list of settings and enter it
4. Select "Auto search for digital stations"
5. A source selection window will open - select the TV connection type. Select "cable"
6. In the scan type selection item, select the “full scan” mode
6.1 Or select "Manual"
6.2 Next, enter the Frequency: 322,000 (KHz) (322 MHz)

Modulation: 64 (QAM) (QAM type)
6.3 Leave the access code as “Auto”. Next, enter the symbolic rate 6750

7. Click "start"
Wait until the TV finishes searching for channels.

Please note bottom part OSD menu Your TV. The bottom menu bar displays hints on which remote control buttons to perform certain actions in the TV menu.

1. Turn off the TV and install the conditional access module. Turn on the TV. Go to the menu. Select the language Russian.

2.Go to the DTV manual setup tab and click OK

3.Enter frequency 322,000 KHz, modulation 64, symbol rate 6750

4.After pressing the OK button, a search will begin, as a result of which the channels should be found.

2.Indicate the country Finland or Germany

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Auto Channel Update: Off

1. In order to set up digital TV channels for the vast majority of Samsung models, press the “Menu” button on the remote control, the TV menu will open in which you will need to select the “Channel” section (Satellite dish icon). In the “Antenna” tab, specify the connection type “Cable”. Go to the “Country” tab and select the “Other” option. The TV will ask for a pin code, if you have not changed it, you will see 0000

2.Go to “Auto-tuning” Signal source: Cable, Choose the type of channels at your discretion, you can only find digital channels, or digital + analog

3. Specify Search Mode: Quick, Network: Auto, Ident. Networks:-----------, Frequency: 322 000 (KHz) (322 MHz) Bitrate: 6750 (KS/s) (bit rate, symbol rate) Modulation: 64 (QAM) (QAM type)

4.As a result of the search, you should find channels

1.In order to set up digital TV channels high definition for the vast majority of Philips models, press the “Menu” button on the remote control, you will see the TV menu in which you will need to select the “Configuration” section

2.Select the Installation tab. After clicking OK, you will be taken to the second menu field, then go to the Channel Settings tab. After clicking the “OK” button, the third part of the menu will open, where you need to select “Automatic”. Installations". Next you will see a message about updating the channel list, click “Start”

3.Select "Reinstall Channels"

4.In the Country section, you must select Finland, but if this country is not in the proposed list, then select Germany

5.Since you are connecting to digital television via a DVB-C cable network, you must select “Cable”

6.Before you start searching for channels, select “Settings” to manually correct the search parameters

7.Install manual mode transmission speed. In the tab, change the transmission speed manually from the control panel to the desired one. In some TV models, the flow rate is indicated in the “Character 1” tab 6750 “Character 2” is left at 0.

8.Now set the network frequency to manual mode and enter the network frequency 322.00 from the control panel

9.After clicking the done tab, you will again be taken to the channel launch menu, now you can start scanning

10.If you did everything correctly and saved all the changed parameters, then during the search your channels will be detected.

1.In order to set up high-definition digital TV channels for the vast majority of LG models, press the “Menu” button on the remote control, the TV menu will open in which you will need to select the “Options” section

3.Now go to the “Settings” menu, “Auto search” item and specify the method of connecting to the TV “Cable”

4.Now in the window that opens, go to “Settings” and enter the following parameters:

Search type:fast, Frequency: 322 000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type), Network ID: auto

5.If you did everything correctly and saved all the changed parameters, then during the search you will find channels and radio stations

6.Important feature LG TVs have the “Automatic channel update” function. It must be disabled, otherwise the TV will periodically reset the channel list you have configured.

Go to "settings" digital cable»:

Auto Channel Update: Off

3.Now go to the “Settings” menu, “Auto search” item and specify the method of connecting to the TV “Cable”
An important feature of LG TVs is the “Automatic channel update” function. It must be disabled, otherwise the TV will periodically reset the channel list you have configured. Auto Channel Update: Off

4.Now in the window that opens, go to “Settings” and enter the following parameters:

Search type:fast, Frequency: 322 000 (KHz) (322 MHz)

Bitrate: 6750 (KS/s) (bit rate, symbol rate)

Modulation: 64 (QAM) (QAM type), Network ID: auto

5.If you did everything correctly and saved all the changed parameters, then during the search you will find channels and radio stations

3. Select the source “Cable TV”

4. Operator “Other operators”

5. Enter the following parameters: Use the left/right arrows to select the scanning type, the name “Fast” Frequency 346000 kHz Symbol rate, Modulation, network ID “Auto” Check the box “Skip encoded channels and press “OK”

6. Check the box for “Digital only” and click “Run”. The TV setup will begin. When finished, exit the menu. Your TV is set!

1. Press the “HOME” button on the TV remote control.

2. The main menu will appear on the TV screen. Select “Settings”

3. In the window that appears, select “Broadcast”.

4. Select “Auto-tuning options”

5. Select “Auto Configuration”

6. In the channel scanning menu, set the following parameters:

Antenna “Cable” Channel type “Digital” Operator selection “Other” Search mode “Network”

7. Start Scanning. Wait until the search is completed.

6. Enter the following parameters: Scan type Name Quick Chat setting Manual. Frequency 346 MHz Setting the network ID “Auto” Then select “Start”, the channel search process will begin.

7. When finished, click “Continue”, the setup is complete.

Press the "HOME" button on the TV remote control.

The main menu will appear on the TV screen. Depending on the version of the operating system, the menus and items may differ; below are two examples various options menu. Option 1. Scroll down the menu and select the “Settings” → “Settings” section

Option 2: Scroll down the menu and select “Settings” → “System Settings”

In the window that appears, select “Channel settings”.

Select “Digital.” Configuration"

In the “Digital Configuration” section, select “Digital Setup”

In the next menu, select “Auto search for digital channels”

TV connection type “Cable TV Other”

Next, confirm searching for channels. Wait for the procedure to complete and exit the menu. Your TV is tuned!

3) Then you need to point the TV and receiver remote controls at each other and press the programmable button on the TV remote control once, in our case the TV power button. After this, the “SET” button indicator will blink twice and turn red.

4) To exit the programming mode, you need to press the “SET” button again, after which the indicator will turn off.

To program the remaining buttons, you need to perform the previous steps from points 1 to 4.

Digital receivers Topfield

To view the TV Guide, you must press the EPG button on the digital receiver control panel. Will open information window. Information about the number and name of the TV channel will be shown at the top. Below is a table, on the left side of which the broadcast time of the TV show is indicated, and in the center - the shortened name of the TV show. You must wait a few seconds for the full list of programs to appear. By moving through the list by pressing the up and down buttons on the remote control, you can view all programs for the current day, while reading their full name and brief description in the lower right corner. The lowest window serves as an assistant for working with the TV Guide. When pressed specified buttons it is possible to: change the type of TV Guide, move to the next days, go back, view the TV Guide of the next and previous channel only for this digital package, while simultaneously viewing the program you are interested in in the upper right corner. To close the TV Guide, you must press the EPG or EXIT button on the remote control.

Digital receivers Signal

To view the TV Guide, you must press the EPG button on the digital receiver control panel. An information window will open. Helpful information about using the EPG will be shown at the top. Below is information about the date, name current program and a brief description of it. Within a few seconds, the complete list of programs in this digital package will be downloaded. After downloading, select the channel we are interested in and click OK. A table will appear, on the left side of which information about the broadcast time of the program is indicated, and on the right side - short name channel. By moving through the list by pressing the up and down buttons on the remote control, you can view all the programs, while reading their title and brief description in the lower right corner, while simultaneously viewing the program you are interested in in the upper right corner. To go back, press the OK button on the remote control. To close the TV Guide, press the EXIT button on the remote control.

INTEK digital receivers

To view the TV Guide, you must press the EPG button on the digital receiver control panel. An information window will open. Information about the number and name of the TV channel will be shown at the top. Below is the name of the current program and its brief description. In the table that appears at the bottom of the screen, a few seconds after entering the EPG, the full list of programs will be loaded. To view it, you need to move by pressing the button on the remote control to the right and left. In this case, information about the name of the program and its brief description will be displayed in the upper left window, and the transmission time will be displayed under the right top window the program you are watching. To close the TV Guide, press the EPG or Back button on the remote control.

BBK SMP127HDT2 - review digital receiver.

In that article I will review the BBK SMP127HDT2 digital receiver. BBK is famous brand, according to statistics, every third family in Russia has at least one device released under the name BBK.

The model is assembled on the basis of the Ali 3812 chipset. Available over-the-air receiver DVB-T standard, DVB-T2, MPEG-2/MPEG-4 with signal reception on a regular home antenna. There is a built-in HD media player with MKV support, it is possible to record TV signal. There are HDMI and composite outputs, you can connect this set-top box to any TV. In these consoles we have a fairly high-quality set of functions.

Let's see what is included in the package of the BBK SMP127HDT2 receiver.

Low frequency wire for connecting to TV,

Instructions - warranty card, 12 month warranty,

Two batteries for the remote control,

Remote control,

Receiver.

The body of the receiver is plastic, except for the bottom and rear panels, it is all glossy. The assembly is high quality and neat. On the front panel there is USB input and power indicator. If the indicator is green, the set-top box is turned on, if the indicator is red, it is turned off. USB port serves to connect a flash drive or hard drive, we can record on them television programs and play movies, music, etc.

On the back panel there is: power cord, antenna input, composite output (bells) and HDMI output. If you need an HDMI cable, you must purchase it separately.

Now let's get acquainted with the menu and set up channels. We connect the set-top box to the TV with an HDMI cable. We connect it to the network and also connect antenna cable. We press the power button on the remote control, the LED on the set-top box changed color, turned green, and the set-top box turned on. After switching on, a preliminary menu appears in which you can configure the starting settings.

Our goal is to get to the main menu, get acquainted with it, and implement quick setup to television channels operating in the DVB-T2 standard. Press the EXIT key on the remote control and get to the main menu of this console.

There are five items in the menu:

Media player, all items gray they will be available as soon as we connect a flash drive or hard drive,

Channel editor, here the sub-items are also gray, since the channels are not configured,

Installation, here you will tune in to television programs, we will return to it later,

System settings,

Settings, here you can find information about this device, factory settings, games and the ability to update via USB.

We return to the “installation” item, go to “DVBT setup”. Three sub-items appear: channel search, auto search and sort. If the antenna is oriented in the right direction, then you can use auto search, and the set-top box will scan the entire frequency range, this is a rather lengthy process. Therefore, we go to the channel search (manual search).

Select a channel in in this case I choose 35 (relevant for St. Petersburg) this is the first multiplex. Select search, click OK, and the set-top box within a few seconds finds the channels that are present on this frequency channel. The search is completed and click OK.

In order to find the second multiplex, we go to channel 45 (relevant for St. Petersburg). Select search and click OK. The set-top box also quickly finds the second ten channels. The search is completed, click OK. We leave the menu and get to the television channels. Click OK and a window will appear with full list found channels, through which we can quickly move channels.

No problems with setup television channels no if you have decimeter antenna It will be enough to connect it to this console. Connect the set-top box itself to the HDMI cable (if the TV is new) or with bells (if the TV is old).

Video instructions.

Appearance digital television caused a kind of excitement, since the content in digital quality became available to a wide range of users. IN lately It is this area of television that is developing very actively; a large number of offices have appeared that will provide services for connecting and setting up digital television for a fee. The good news is that set up digital television on TV you can do it yourself.

So in this article we will look in detail at all aspects of setup, both in general and for TVs from specific manufacturers. It is worth noting that there are various types digital television. All proposed schemes relate to cable “digital”.

General instructions

First let's look at general scheme digital television reception settings. IN various models TVs, the sequence of operations and item names may differ slightly. Don’t worry, next we will look at the configuration features for specific brands, all points will be illustrated.

1. Using the remote control, enter the menu of your TV. In the window that appears, select the “Options” item. In order to go directly to the configuration, you must select the “Auto Configuration” item. A window should appear on the screen asking you to select one of the signal sources: cable or antenna. Select the first option, and then click the “Start” button.

2. After the operations have been completed, a window should appear in which you must select “Digital” as the signal source and then press the “Start” button again.

3. We are at the final stage of setting up digital television. In the window that appears, we find the “Search Mode” item, several options will appear, we need the “Full” item. Click and fill in all fields with the data indicated below.

Frequency (kHz) - 314,000 (314 MHz).

Modulation - 256 QAM.

Transfer speed - 6875 kS/s.

Please note that some TV models support network search. This means that you do not need to manually specify the above parameters. Just after choosing required regime search, click the “Search” button. As you can see, setting up digital television on your TV is quite simple. For those who are confused, read on for the illustrated instructions.

It is logical to assume that different TV models from the manufacturer LG use their own firmware and their own menu. However, in general, the menu of all TVs has characteristic similarities. Find the “Menu” button on the remote control, press it and a window appears on the screen in which you need to select the “Options” item.

In the “Options” tab you will see several parameters available for change. In the “Country” item you must indicate either Germany or Finland.

After this, you need to go to the “Settings” menu, there select the “Auto search” item in which you specify “Cable” as the connection method.

After the completed manipulations, a window should open in which you need to select the “Settings” item and specify all the values as in the figure below.

If you followed all the instructions correctly, then after searching, the TV will detect all available channels, as well as radio stations.

Please note that LG TVs use an automatic channel update feature that, at certain intervals, resets the existing channel list and starts new search. For convenience, it is advisable to disable this feature. To do this, go to the “Digital cable settings” tab and turn off automatic update. Thus, setting up digital television on LG TVs is quite simple. All it takes is a little care.

Setting up digital television on TVs Philips

So, find the “Menu” button on the remote control and use it to go to the menu of your TV. Next, you need to go to the “Configuration” section.

In the window that appears, click on the “Install” item, after which a secondary menu will appear on the TV screen, in which you need to select the “Channel setup” section. Another submenu will appear, in which we select the “Automatic” item. Settings". If you have completed all the transitions correctly, a message should appear warning you about the upcoming update of the list of all channels. Click “Start”.

Go to the section"Country" and select either Finland or Germany from the list.

For connection method, select"Cable".

Before you start the channel search process, go to the “Settings” item and make the settings according to the images below.

Now you have managed to set up digital television on your Philips TV. You can start directly searching for channels; to do this, click “Start”.

Setting up digital television on TVs Samsung

On the remote control, press the “Menu” button. Your TV menu should appear on the screen. Go to the “Channel” section (shown as satellite dish). Several tabs will appear on the right, select “Antenna” and select “Cable” as the connection type. Next, you need to go to the “Country” tab and specify the “Other” parameter. In this case, the TV should request a pin code. If you did not change it yourself, then enter 0000 (default value).

Go to the “Auto Configuration” tab and select “Cable” as the signal source.

Set all parameters as in the image below, then click “Search”.

After all operations, your TV will detect all available channels.

Setting up digital television on TVs Toshiba

Using the “Menu” button, go to the TV menu and select the Russian menu language.

Find the "DTV Manual Tuning" tab.

Manually enter all the parameters as in the image below.

After that, click “Ok”, the search for channels will begin.

Conclusions

We have discussed in detail the diagram of how to properly set up digital television on your TV. We supported all sequences with images for better perception. If you have any questions, please use the form feedback our website or ask a question in the comments.