Complete network reset. netsh winsock reset command to reset the network protocol stack

There are a lot of problems with the Internet in Windows 10. What can you find in the comments to various articles on our website. I have already written many instructions for the solution different problems which are most often encountered Windows users 10. And if almost every problem or error occurs, I would advise resetting the network settings. This very frequency procedure is a solution to many different, and sometimes even incomprehensible, problems.

In Windows 10, you can reset network settings through the settings. This opportunity appeared after installing update 1607. Previously, it was possible to reset the DNS cache, TCP/IP protocol settings, etc. only through the command line, using special teams. In principle, this can be done now by executing the necessary commands, but you can make everything much simpler by clicking on one button in the settings.

Resetting the network (Internet) settings itself will completely clear all network settings and reinstall network adapters. Wireless adapter(if it exists), and a network card. In other words, after a reset network settings and reboot, everything related to the network and Internet connection will be cleared to factory settings. To the state that was immediately after installing Windows 10.

This method can help solve huge amount errors. Among which:, error, when, or an error appears in Windows 10. Only if the problem is with your computer, and not with the Internet provider, or with the Wi-Fi router.

Moreover, resetting network settings can be useful for problems that users face during the process. Wi-Fi distribution in Windows 10. I recommended this method in the article. Only there I showed how to reset TCP/IP parameters via the command line.

Important point! As I already wrote above, this procedure Completely remove all Internet connection parameters and network settings. If you have some kind of Internet connection configured, you will need to configure it again. If you can’t do it yourself, then see the article: . In any case, you need to be prepared for the fact that after the reset the problem will remain, or even get worse.

How to reset Internet settings and network settings in Windows 10?

Everything is very simple here. Open "Start" and go to "Settings".

Go to the "Network and Internet" section.

On the "Status" tab, click on "Network reset".

Click on the "Reset now" button.

Confirm the reset by clicking “Yes”.

The computer will restart.

All network settings will be reset to factory settings. If you had problems connecting to the Wi-Fi network, try connecting again. If the Internet is connected directly to the computer and you need to configure a connection (PPPoE), then create it. Or try starting the access point if you had problems with this.

Friends, hello everyone! In this article we will again talk about resetting network Windows settings dows 7 and 10. Although over time nothing has changed in this regard, which means for the good old XP this instruction will do too.

If you remember, there was already a thread on this topic, but the other day when troubleshooting network problems, it didn’t help me. The fact is that the combination of commands indicated in it did not work this time. For unknown reasons, the command line reported that it does not know such parameters.

So I went back to the official help Microsoft to find a way out of the current situation. And this is what I came to in the end.

How to reset network settings of Windows 7, 10 and XP with one command?

First, you need to run the command prompt as an administrator. How to do this was detailed. Next, we write in it just one line like this:

Netsh int ip reset resetlog.txt

After this, be sure to reboot the experimental computer. That's it, now everything to the network should be a thing of the past. By the way, if you want to get acquainted in detail with the results of the netsh command (Network Shell - a shell for configuring TCP/IP parameters) using a log file named resetlog.txt, then you can also specify the following command:

Netsh int ip reset c:\resetlog.txt

Now at the root system disk The above file will appear. But the main point is that to successfully perform a reset, the file name at the end of the command must be specified. Also, before starting the process, be sure to write down your current settings network card.

After all, the treatment procedure described in this article will lead to the removal of all effective values IP addresses. Well, friends, this article about resetting the network settings of Win 7 and 10 has come to an end. If so, ask your questions in the comments. And now, as always, let's watch another interesting video.

Is your Windows 10 PC unable to connect to the Internet? Your PC won't connect to Wi-Fi networks? Are you facing network problems on your PC but can't fix them? In this guide we will share in a simple way resolve network problems by resetting network settings to their default values.

Windows 10 - includes new feature called Network Reset, which will quickly return the network settings to default for all network adapters in the system. It can be very useful to reset your network settings if you are having connection problems, especially after uninstalling malware.

"Network Reset" will allow you to remove and reinstall all network adapters, as well as install others network components back to initial settings. You may need to reinstall another network software after that, for example, VPN client software or virtual switches.

Reset network settings in Windows 10.

Step 1: Open the Settings app, the most quick way- press the keyboard shortcut Win+I and go to the section " Network and Internet".

Step 2: Click on the section on the left side of the window “ State".

On the status page, there are several links that allow you to correct your network configuration. One of them is the diagnostic package "Network Troubleshooter", which runs a network scan on your system and will suggest fixes if needed.

If for some reason the Network Troubleshooter does not find any errors and cannot fix your connection, you need to perform a Network Reset.

Since "Reset Network" resets the settings of all network cards, it returns initial settings Winsock, etc. If you have a custom network configuration, make a note of your settings. Also, write down your Wi-Fi configuration and associated passwords before resetting.

Step 4: After that, click the " Reset Now".

Step 5: Click the button Yes" and Windows 10, will reset the network adapters and return to the initial state Winsock.

Please note: Windows10 will automatically reboot after 5 minutes.

Previously, users had to run these commands manually to clear the network adapter configuration and reset Winsock.

netcfg -d
netsh winsock reset

Now you know how to do a Network Reset in Windows 10. Good luck!

Many users encounter a problem when the Internet and network stop working on their computer. Although the modem or router shows that the Internet is working. Therefore, Microsoft added to the operating system Windows opportunity perform a self-reset of the adapter parameters.

This article will tell you how to reset Windows 10 network settings using updated system settings and how to reset network settings via the command line. In any of the cases, the netsh winsock reset command is used, which actually resets the network settings.

Before moving on to resetting network settings, you must first figure out whether it will help in a particular situation. The first symptoms of problems with the system’s network settings can be different, among them it is worth noting the most common:

File download speed is very slow.
After turning on the computer, literally within a few minutes the Internet disappears (although it works as expected for several minutes).
The computer does not automatically obtain an IP address.

All current situations are described in the case of full operation of the Internet from the provider. Resetting network settings is only needed if there is a problem with your operating system.

How to reset network settings in Windows 10

This action will remove and then reinstall all network adapters and return other network components to their original settings. You may then need to reinstall other network software (such as VPN client software or virtual switches).

After confirming the network settings reset, your computer will restart. When you turn on your computer for the first time after resetting the settings, the user will be asked to select the network on which your computer will be serviced.

Until a reset is possible network parameters adapter in updated Windows settings 10 network settings were reset using a different method. The current command line method is also suitable for users previous versions Windows operating system.

If the user receives messages, for example, the DNS server does not respond or the DNS server address cannot be found, then before executing the command netsh winsock reset You can try to reset the DNS cache. To do this you need to run the command ipconfig /flushdns V command line running as administrator.

conclusions

A complete reset of the operating system's network settings is an excellent solution to many problems. Therefore, we looked at how to reset Windows 10 network settings using system settings or through the command line. If necessary, reset the network settings in the previous operating systems you can use the command netsh winsock reset, which actually helps to reset network parameters.

Windows 10 includes a new feature called Network Reset that will quickly return network settings to default for all network adapters on the system. It can be very useful to reset your network settings if you are having connection problems, especially after removing malware.

Network Reset will allow you to remove and reinstall all network adapters, as well as install other network components back to the original settings. You may need to reinstall other network software after this, such as VPN client software or virtual switches.

Open Settings WinKey+I and press Network and Internet

Click State

If for some reason the Network Troubleshooter does not find any errors and cannot fix your connection, you need to Network reset.

Because Reset Network resets all network cards, returns initial Winsock settings, etc. If you have a custom network configuration, make a note of your settings. Also, write down your Wi-Fi configuration and associated passwords before resetting. After that, click the button Reset Now.

Click the button Yes. Windows 10 will reset the network adapters and return Winsock to its original state.

Note: Windows10 will automatically reboot after 5 minutes.

Previously, the user had to run these commands manually to clear the network adapter configuration and reset Winsock.

netcfg -d
netsh winsock reset

Now you know how to do a Network Reset in Windows 10.

In the instructions on this site related to problems with the Internet, such as, and others, among the solutions there is always a reset of Windows network settings ( DNS cache, TCP/IP protocol, static routes), usually using the command line.

The Windows 10 1607 update introduces a feature that makes it easier to reset all network connections and protocols, literally with the click of a button. That is, now, if any problems arise with the operation of the network and the Internet, and provided that they are caused by incorrect settings, these problems can be solved very quickly.

Resetting network and Internet settings in Windows 10 settings

When performing the steps below, keep in mind that after resetting your Internet and network settings, all network settings will return to the state they were in when you originally installed Windows 10. That is, if your connection requires you to enter any settings manually, you will have to repeat them.

To reset network settings, network adapter settings, and other components in Windows 10, follow these simple steps.

After clicking the button, you will need to confirm resetting the network settings and wait a while for the computer to reboot.

After rebooting and connecting to the network, Windows 10, as after installation, will ask you whether this computer should be found on the network (that is, your network is public or private), after which the reset can be considered complete.

Note: This process removes all network adapters and reinstalls them on the system. If you previously had problems installing network card or Wi-Fi adapter drivers, there is a chance that they will happen again.

Resetting the network adapter

Right-click on the network icon in the notification panel. Select. Next, in a new window, click on Change adapter settings. A window will open with access to the Internet.

If you need to change the settings for connecting via a network cable, then click right click mouse to adapter Ethernet. If to connect via Wi-Fi, then the connection Wireless network. Select an item Properties.

In a new window you can set automatic receipt addresses for of this adapter (by highlighting the items Obtain an IP address automatically and Obtain a DNS server address automatically), or set addresses statically.

After making changes, do not forget to apply the settings by clicking on the button Ok.

Restart your computer and try connecting to the Internet.

Instructions for Windows 7

In Windows 7, everything is done exactly the same as on Windows 8. It would be possible not to write separately for the seven, but so be it.

Right-click on the network icon, then select Network and Sharing Center. Next, click on I Changing adapter settings, and again right-click on the adapter whose properties we want to change. Select from the menu Properties. Like this:

Select the item Internet Protocol Version 4 (TCP/IPv4) and press the button Properties. We indicate the required IP and DNS, or set them to be received automatically, and click Ok.

Setting up automatic obtaining (or setting static) IP and DNS on Windows XP

Press Start and open Control Panel. Then, select Network and Internet connections.

aligncenter wp-image-8033 colorbox-8012" src="http://kirensk.net/images/up/28-08-2014-15-12-45.jpg" alt="Network connections in Windows XP" width="649" height="446">!}

We see network connections that are available on our computer. Right-click on the desired connection and select Properties.

Select an item Internet Protocol (TCP/IP) and press the button Properties.

As in the two systems that I wrote about above, we set the parameters we need for obtaining IP and DNS. Either receive automatically, or set static addresses and click Ok.

sfc /scannow

HKLM\SYSTEM\CurrentControlSet\Services\LanmanServer
HKLM\SYSTEM\ControlSet001\Services\LanmanServer
HKLM\SYSTEM\ControlSet002\Services\LanmanServer

Sometimes, it happens that the Internet connection settings go wrong or simply does not want to connect to the network (does not receive an IP address via DHCP). Similar problems can occur as a result of the operation of certain malicious programs (viruses). You can torture those for a long time. support from your provider or call a specialist at home. You can try to fix the problem yourself.
To reset TCP/IP in Windows NT (2000/XP/Seven) operating systems, there is special program netsh.exe.

netsh.exe- (Network Shell) allows you to configure network parameters.

Some nasty viruses get into WinSock and cause mischief.
Symptoms:

The speed of downloading files via TCP is very low (while downloading via UDP can be fast);

When you turn on the computer for a while, a couple of minutes, the Internet works fine, but then it disappears completely (the speed drops to 0);

The Internet works and the download speed is normal, but the downloaded file turns out to be broken because it is not downloaded completely (most likely the virus intercepts some of the packets during transmission, but sends a notification to the source that all packages have been successfully received).

In addition to viruses, you can also “break” your Internet connection yourself (or it “got wrong”)

Some examples:

The computer does not receive an IP address automatically (via DHCP);

IP addresses are pinged but not names;

The computer receives an IP address of the following type: 169.254.*.*;

If you have cleared yourself of viruses, you can begin recovery. ATTENTION! The following procedures will reset your network settings. I strongly recommend rewriting the settings.
To reset Winsock:

If the first command did not help solve the problem, you can reset the TCP/IP stack to factory settings:
There in the command line, enter the command:

netsh int ip reset c:\resetlog.txt

In this case, the reset log will be saved in the root of the C:\ drive, if you omit the c:\ prefix, the log will be saved in current directory. After this, you should restart your computer.

After using this command, the following registry branches will be reset to factory settings:

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\
SYSTEM\CurrentControlSet\Services\DHCP\Parameters\

You can use these commands together one after the other. By the way, they also reset the DNS cache.
About DNS cache problems: For example, the site moved to another hosting, as a result its IP address changed. And since you have some not quite fresh data in your cache, when you enter the site name, you will be taken to the old IP address, where the site no longer exists.

To avoid resetting all settings, try the command ipconfig /flushdns If it doesn't help, use netsh int ip reset resetlog.txt- this is guaranteed to help and reset everything related to network connections.

Reset the TCP/IP and Winsock protocol stack.

One of the components of connecting to the Internet on a computer is a built-in set of instructions called TCP/IP. Sometimes TCP/IP is damaged (consequences of some viruses, installation incorrect drivers network card and so on.). If you can't connect to the Internet and have tried everything to solve the problem, it is possible that the problem is the TCP/IP protocol.

Since TCP/IP is a component Windows kernels, it cannot be deleted. However, you can reset TCP/IP to initial settings using the NetShell tool ( netsh).

Signs:
a) I can’t connect to the Internet or