Circuit of a high-voltage converter from a line transformer. A simple powerful kacher on a line transformer

Linear transformers are among the most commonly used by high voltage hobbyists, mainly due to their simplicity and availability. Every CRT TV (big and heavy) that people throw away now has such a transformer.

Unlike many transformers found in other electronics, which are designed to handle regular 50Hz alternating current, and step-down transformers, the line transformer operates at a higher frequency, around 16KHz and sometimes higher. Many modern line transformers produce direct current. Old line transformers produced alternating current, which allowed you to do anything with them. AC line transformers are more powerful because they do not have a built-in rectifier/multiplier. DC line transformers are easier to find and are recommended for this project. Make sure your line transformer has an air gap. This means that the core is not a closed circle, but rather resembles the letter C, with a gap of about a millimeter. Almost all modern horizontal transformers have it, so if you are using a modern horizontal transformer, you don’t have to check this.

This circuit uses the 2N3055 transistor, which is what builders of line transformers love and hate. They are loved for their availability and hated because they usually stink. They tend to burn out quite spectacularly, but the circuit works incredibly well with them. The 2N3055 got a bad reputation when used in simple single-transistor circuits in which high voltage is present across the transistor. This circuit adds several parts that significantly increase its power output. The theory of operation of the circuit is written below.

Scheme

There are very few elements in this circuit, and they are all described on this page. And many parts can be replaced.
The value of the 470 Ohm resistor can be changed. I used a 450 ohm resistor made from three 150 ohm resistors connected in series. Its value is not critical for the operation of the circuit, but to reduce heating, use the maximum resistor value at which the circuit operates.
The lower resistor value can be changed to increase power. I'm using a 20 ohm resistor made from two 10 ohm resistors connected in series. The lower its value, the higher the temperature and the shorter the operating time of the circuit.

The capacitor located next to the transistor (0.47 µF) can be replaced to increase power. The higher its value, the higher the output current (and arc temperature) and the lower the voltage. I settled on a 0.47uF capacitor.
The number of turns on the feedback coil (three-turn coil) can change the power output. The more turns, the greater the current, but not the voltage.

This circuit differs from the more common single-transistor casser in that a diode and a capacitor are added to it, which is connected in parallel with the diode. The diode protects the transistor from voltage surges of reverse polarity, which can burn the transistor. You can use a different type of diode. I used a GI824 diode taken out of the TV. When choosing a diode, pay attention to the voltage and switching speed. To find out if your diode is suitable, find the datasheet for the BY500 diode, and then for your diode and compare the parameters. If your diode is comparable to or better than this one, then it is suitable.

The capacitor is the key to high power output. The transistor generates a frequency set mainly by the primary coil and the feedback coil. The capacitor and primary winding form an LC circuit. The LC circuit operates at a specific frequency, and if you tune the circuit so that this frequency is the same as the transistor frequency, the output power will increase significantly. The theory of an LC circuit is similar to that of a Tesla coil. This circuit can be customized by changing the capacitor value and the number of turns on the primary/secondary windings.
This circuit requires a powerful power supply, which is described below.

power unit

The circuit requires a powerful DC power supply with an output voltage of 12 to 30 volts and 1 to the number of amps you desire. It's a good idea to make a regulated power supply so that the circuit receives exactly the voltage it needs. If the circuit is not assembled correctly and a power supply like this is used, the circuit will burn out. But regulated voltage is not necessary for normal operation.

I used a 300 watt transformer from the amp. It has windings for 2, 4, 15, 30 and 60 volts. The circuit requires 12 to 18 volts for the 2N3055. I often run the circuit at 30V, but not for long, and the transistor is mounted on a powerful radiator. At 15V, the circuit can operate indefinitely, since after 30 minutes of operation, the temperature did not exceed room temperature.

The alternating current from the transformer goes to a 400 W bridge rectifier mounted on the radiator, and from it to a 7800 uF 70V capacitor to smooth out the voltage. Using similar components, you can make your own power supply.

Also, switching power supplies or UPS can be used as a power supply. They are found in laptop chargers, car battery chargers and computer power supplies. They often have a 12V output and a current of up to 10A, which is suitable for this circuit.

This is a very simple circuit to assemble. My assembly is not an instruction or an example, but you can repeat it. Everything is mounted on a piece of MDF, and the elements are laid out loosely to minimize interference from nearby wires and allow for cooling. Use stranded wire. Numerous photographs show in detail the various elements of the circuit, which are often more useful than words.

One of the most important points in the assembly is the transistor heatsink. 2N3055 is manufactured in the TO-3 package. You can buy TO-3 radiators, but they are a little hard to find. I used a heatsink from a computer processor with holes for its contacts on the flat side. Wires from the contacts pass between the blades. The transistor is attached to the radiator with self-tapping screws. Remember to use thermal paste between the transistor and the heatsink. The wires going to the line transformer are attached to it using alligator clips so that line transformers can be changed for experiments.

Another important point is the windings of the line transformer. Enamel insulation of copper wire is good, but it is better to add additional insulation between the core and the windings. The core may have sharp edges, and if the enamel is peeled off, a short circuit may occur. When winding the coils, I removed the metal clamp holding the halves of the transformer together, wound the coils, and then installed it again. On some transformers this is not possible, and the wire will need to be wrapped around the core. The windings must be wound out of phase, which means they wind around the core in opposite directions. This is shown in the photographs.

Usage

When using this circuit, do not perform any manipulations with the connected wires. Also check the temperature of the transistor and resistors during operation, but do this only when the device is unplugged. If any element is noticeably warm, then do not turn on the circuit until it cools down. Capacitors can retain a dangerous charge, so be careful.

Also, wear rubber-soled shoes when working with high voltages and touch the device while it is on with only one hand. Make sure the circuit has been connected to ground after operation to avoid electric shock. Do not attempt to configure an enabled circuit.

There are many things you can do with this circuit, such as using it to power a Tesla coil, melt salt, or just have fun with electric arcs.

List of radioelements

Designation Type Denomination Quantity NoteShopMy notepad
Bipolar transistor

2N3055

1 KT819GM To notepad
Rectifier diode

BY500-200

1 200 B To notepad
Electrolytic capacitor4700 uF 25V1 To notepad
0.47 µF 200V1 To notepad
Resistor

Linear transformers are used to create scans on a TV. The devices are enclosed in a housing that protects adjacent parts from high voltage. Previously, in color and black-and-white televisions, accelerating voltage was obtained using a horizontal transformer. The circuit used a multiplier. A horizontal high-voltage transformer transmitted the converted electrical signal to the presented element. The multiplier generated the focusing voltage, ensuring the operation of the second cathode anode.

Today, a diode-cascade horizontal scanning transformer (TDKS) is used in TV circuits. What such equipment is, how to check it yourself and make repairs will be discussed further.

Peculiarities

Transformers of the TDKS type are today included in the TV circuit to provide the anode (second) kinescope with electric current with the required parameters. Outgoing voltage is 25-30 kV. During operation of the equipment, an electrical flow is generated. This accelerating voltage is 300-800 V.

Depending on the category of TDKS transformers, pinout, a secondary voltage is generated, which is additional to ensure frame-type scanning. Equipment devices pick up a signal from a kinescope beam at an automatically adjusted horizontal scan frequency in TV transformers.

The connection diagram and pinout in the presented transformer characterize the device. The device has a primary winding. An electric current is supplied to it for further development. The primary circuit supplies power for the operation of video signal amplifiers. The winding transmits electricity to the secondary coil. From here the power is supplied to the corresponding circuits.

Video: Line transformer

The line transformer is responsible for powering the second anode, accelerating voltage, and focusing. These processes are carried out in TDKS. Adjustment occurs using potentiometers. Transformers of the presented category are provided with a certain pinout. The pin arrangement can be in the form of the letter O or U.

Breaking

Line devices may fail. In this case, the operation of the TV and monitor will be impossible. There are many varieties of row aggregate models. Replacement is difficult. The cost of analog devices is high. Some TVs and monitors require large repair costs. The necessary parts are sometimes difficult to find.

In order to purchase only that part of the circuit that has failed and quickly replace it, you need to check the line transformer. It will be easier for the TV to undergo adequate repairs. First of all, check for the following faults:

  1. Circuit break.
  2. Breakdown of the sealed housing.
  3. Short circuit between turns.
  4. Potentiometer break.

The first two breakdowns are quite easy to identify. This is determined visually. To replace faulty elements, material can be purchased at almost any radio equipment store.

It is more difficult to determine a short circuit in the winding circuits. In this case, the transformer produces a sound resembling a squeak. But repairs are not always required when such a signal appears. TDKS sometimes beeps due to high voltage on the secondary circuit. Check what is causing the sound using a special device. If there is no equipment, you need to look for other options.

Checking with an oscilloscope

If the TV needs to be checked in the TDKS system, the check is performed using an oscilloscope. To repair the TV, you will need to cut off the power supply to the device. Next you need to find the secondary circuit. Its operation is examined when connected to the cut-off power supply terminal of the TDKS through R-10 Ohm. Replacement or repair of the device will be required if the connection to the oscilloscope reveals abnormalities. The following deviations are possible:

  • The interturn short circuit shows a “rectangle” with large noise at R=10 Ohm. Almost all the tension remains here. If there is no fault in this area, the deviation will be determined by fractions of a volt.
  • If there is no secondary voltage, the circuit needs to be replaced. There was a break.
  • When R=10 Ohm is removed and a load of 0.2-1 kOhm is created on the secondary circuit, the load at the output is estimated. It should repeat the incoming indicators. If there is a deviation, the TDKS must be repaired or completely replaced.

There are other breakdowns as well. You can identify them yourself.

Restoring the device

Independent replacement and repair of TDKS is quite possible. Having determined the malfunction, you can restore the system. When considering how to connect a line transformer to televisions, it is necessary to study the procedure for resuming its operation. In the event of a complete replacement of a transformer device, it will be necessary to select new equipment with an appropriate terminal system. Only in this case will the technique work correctly.

If the equipment does not work due to a breakdown, it means that a crack has appeared in the housing. You can find it upon inspection. The crack will need to be cleaned, degreased, and then filled with epoxy glue. In this case, the resin layer must be at least 2 mm. This will prevent breakdown in the future.

Repairing the TDKS if the circuit breaks is problematic. You will need to rewind the reel. This is a labor-intensive process that requires high concentration from the master throughout the entire procedure. Replacing the winding is possible, but this requires some experience.

If the filament winding breaks, the line is formed from another place. In this case, insulated wire is used. The cable is wound around the core. The voltage is set by using a resistor.

Other breakdowns

There are many reasons why TDKS does not work. Experienced radio amateurs can help you examine common faults.

If a transistor is broken in the device, you need to remove it and measure the collector voltage without it. If the indicator is determined to be too high, it is adjusted to the required value. If it is impossible to perform such a procedure, you need to change the zener diode in the power supply. You definitely need to install a new capacitor.

It is recommended to check soldering on all connectors. If necessary, it is strengthened. If such a problem is detected on the capacitors, they are soldered off. Examination may reveal blackening. You will need to purchase a new part. If the rectangular capacitors are swollen, they should also be replaced. If rosin remains are visible, they should be removed with alcohol and a brush.

If the transistor constantly breaks through in the line scan, the type of malfunction should be determined. The breakdown can be thermal or electrical. It is a faulty transformer that leads to such a problem.

Interesting video: High voltage on TDKS

Having examined the features of line transformers, as well as their possible malfunctions, you can carry out repair work yourself. In this case, there is no need to purchase new, expensive equipment. In some cases, it will not be possible to repair the monitor without such actions. Not every kinescope has TDKS devices on sale today. Therefore, replacing faulty parts is sometimes the only acceptable solution.

From this article you will learn how to obtain high voltage, high frequency with your own hands. The cost of the entire structure does not exceed 500 rubles, with a minimum of labor costs.

To make it, you will need only 2 things: - an energy-saving lamp (the main thing is that there is a working ballast circuit) and a line transformer from a TV, monitor and other CRT equipment.

Energy saving lamps (correct name: compact fluorescent lamp) are already firmly established in our everyday life, so I think it won’t be difficult to find a lamp with a non-working bulb, but with a working ballast circuit.
The CFL's electronic ballast generates high frequency voltage pulses (typically 20-120 kHz) that power a small step-up transformer, etc. the lamp lights up. Modern ballasts are very compact and easily fit into the base of the E27 socket.

The lamp ballast produces voltage up to 1000 Volts. If you connect a line transformer instead of a lamp bulb, you can achieve amazing effects.

A little about compact fluorescent lamps

Blocks in the diagram:
1 - rectifier. It converts alternating voltage into direct voltage.
2 - transistors connected according to the push-pull circuit (push-pull).
3 - toroidal transformer
4 - resonant circuit of a capacitor and inductor to create high voltage
5 - fluorescent lamp, which we will replace with a liner

CFLs are produced in a wide variety of powers, sizes, and form factors. The greater the lamp power, the higher the voltage must be applied to the lamp bulb. In this article I used a 65 Watt CFL.

Most CFLs have the same type of circuit design. And they all have 4 pins for connecting a fluorescent lamp. It will be necessary to connect the ballast output to the primary winding of the line transformer.

A little about line transformers

Liners also come in different sizes and shapes.

The main problem when connecting a line reader is to find the 3 pins we need out of the 10-20 they usually have. One terminal is common and a couple of other terminals are the primary winding, which will cling to the CFL ballast.
If you can find documentation for the liner, or a diagram of the equipment where it used to be, then your task will be significantly easier.

Attention! The liner may contain residual voltage, so be sure to discharge it before working with it.

Final design

In the photo above you can see the device in operation.

And remember that this is constant tension. The thick red pin is a plus. If you need alternating voltage, then you need to remove the diode from the liner, or find an old one without a diode.

Possible problems

When I assembled my first high voltage circuit, it worked immediately. Then I used ballast from a 26-watt lamp.
I immediately wanted more.

I took a more powerful ballast from a CFL and repeated the first circuit exactly. But the scheme did not work. I thought the ballast had burned out. I reconnected the lamp bulbs and turned them on. The lamp came on. This means it was not a matter of ballast - it was working.

After some thought, I came to the conclusion that the ballast electronics should determine the lamp filament. And I used only 2 external terminals on the lamp bulb, and left the internal ones “in the air”. Therefore, I placed a resistor between the external and internal ballast terminals. I turned it on and the circuit started working, but the resistor quickly burned out.

I decided to use a capacitor instead of a resistor. The fact is that a capacitor passes only alternating current, while a resistor passes both alternating and direct current. Also, the capacitor did not heat up, because gave little resistance to the AC path.

The capacitor worked great! The arc turned out to be very large and thick!

So, if your circuit does not work, then most likely there are 2 reasons:
1. Something was connected incorrectly, either on the ballast side or on the side of the line transformer.
2. The electronics of the ballast are tied to working with the filament, and since If it is not there, then a capacitor will help replace it.

HV blocking generator (high voltage power supply) for experiments - you can buy it on the Internet or make it yourself. To do this, we need not very many parts and the ability to work with a soldering iron.

In order to assemble it you need:

1. Line scan transformer TVS-110L, TVS-110PTs15 from tube b/w and color TVs (any line scanner)

2. 1 or 2 capacitors 16-50V - 2000-2200pF

3. 2 resistors 27 Ohm and 270-240 Ohm

4. 1-Transistor 2T808A KT808 KT808A or similar characteristics. + good radiator for cooling

5. Wires

6. Soldering iron

7. Straight arms


And so we take the liner, disassemble it carefully, leave the secondary high-voltage winding, consisting of many turns of thin wire, a ferrite core. We wind our windings with enameled copper wire on the second free side of the ferite core, having previously made a tube around the ferite from thick cardboard.


First: 5 turns approximately 1.5-1.7 mm in diameter

Second: 3 turns approximately 1.1mm in diameter

In general, the thickness and number of turns can vary. I made what was at hand.

Resistors and a pair of powerful bipolar npn transistors - KT808a and 2t808a - were found in the closet. He did not want to make a radiator - due to the large size of the transistor, although later experience showed that a large radiator is definitely needed.


To power all this, I chose a 12V transformer; it can also be powered from a regular 12 volt 7A battery. from a UPS (to increase the output voltage, you can supply not 12 volts but, for example, 40 volts, but here you already need to think about good cooling of the trance, and the turns of the primary winding can be made not 5-3 but 7-5 for example).

If you are going to use a transformer, you will need a diode bridge to rectify the current from AC to DC, the diode bridge can be found in the power supply from the computer, you can also find capacitors and resistors + wires there.

As a result, we get 9-10 kV output.


I placed the entire structure in the PSU housing. It turned out to be quite compact.

So, we have an HV Blocking generator which gives us the opportunity to carry out experiments and run the Tesla Transformer.

Sometimes it becomes necessary to obtain high voltage from scrap materials. The line scan of domestic televisions is a ready-made high-voltage generator; we will only slightly alter the generator.
You need to remove the voltage multiplier and horizontal transformer from the horizontal scan unit. For our purpose, the UN9-27 multiplier was used.

Literally any horizontal transformer will do.


The horizontal transformer is made with a huge margin; TVs use only 15-20% of the power.
The stitcher has a high-voltage winding, one end of which can be seen directly on the coil, the second end of the high-voltage winding is located on the stand, along with the main contacts at the bottom of the coil (13th pin). It is very easy to find the high-voltage terminals if you look at the circuit of the line transformer.

The multiplier used has several pins; the connection diagram is shown below.


Voltage multiplier circuit

After connecting the multiplier to the high-voltage winding of the line transformer, you need to think about the design of the generator that will power the entire circuit. I didn’t bother with the generator, I decided to take a ready-made one. An LDS control circuit with a power of 40 watts was used, in other words, simply LDS ballast.


Ballast is made in China, can be found in any store, the price is no more than $2-2.5. This type of ballast is convenient because it operates at high frequencies (17-5 kHz depending on the type and manufacturer). The only drawback is that the output voltage has a higher rating, so we cannot directly connect such a ballast to a line transformer. For connection, a capacitor with a voltage of 1000-5000 volts, a capacity of 1000 to 6800 pF, is used. The ballast can be replaced with another generator, it is not critical, only the acceleration of the line transformer is important here.

ATTENTION!!!
The output voltage from the multiplier is about 30,000 volts, this voltage can be fatal in some cases, so please be extremely careful. After turning off the circuit charge remains in the multiplier, short-circuit the high-voltage terminals to completely discharge it. Do all experiments with high voltage away from electronic devices.
In general, the entire circuit is under high voltage, so do not touch the components during operation.


The installation can be used as a demonstration high-voltage generator, with which a number of interesting experiments can be carried out.